关于笔记本上FC5的网卡驱动问题

meaning

笔记本是ASUS的A6J，安装了FC5，过程中没出现什么问题，只是明显显卡、网卡、声卡的驱动都没装好。我打算先装网卡驱动。查了网卡的芯片是realtek8168Gigabit，上realtek主页下载了for linux的驱动。其readme文件我贴出来让大家看看：
======================================================
<Linux device driver for Realtek Ethernet controllers>

  This is the Linux device driver released for RealTek Ethernet controllers, which are listed as following.
        1. RTL8169S/SB/SC (Gigabit Ethernet with PCI interface)
        2. RTL8168B (Gigabit Ethernet with PCI-Express interface)
        3. RTL8101E (Fast Ethernet with PCI-Express interface)

<Requirements>

  - kernel source tree (supported versions 2.4.x or 2.6.x)
  - compiler/binutils for kernel compilation

<Quick install with proper kernel settings>

  Unpack the tarball :
        tar vzxf r1000_vX.YZ.tgz

  Change to the directory:
        cd r1000_vX.YZ

  If you are running the target kernel, then you should be
  able to do :

        make clean modules        (as root or with sudo)
        make install
        depmod -a




<Force Link Status>

1. Force the link status when insert the driver.
        If the user is in the path ~/r1000, the link status can be forced to one of the 5 modes as following command.

        #insmod ./src/r1000.ko speed=SPEED_MODE duplex=DUPLEX_MODE autoneg=NWAY_OPTION

        ,where
                SPEED_MODE        = 1000        for 1000Mbps
                                = 100        for 100Mbps
                                = 10        for 10Mbps
                DUPLEX_MODE        = 0        for half-duplex
                                = 1        for full-duplex
                NWAY_OPTION        = 0        for auto-negotiation off
                                = 1        for auto-negotiation on
        For example:
        #insmod ./src/r1000.ko speed=100 duplex=0 autoneg=0
        will force PHY to operate in 100Mpbs Half-duplex.

2. Force the link status by using ethtool.
        a. Insert the driver first.
        b. Make sure that ethtool exists in /sbin.
        c. Force the link status as the following command.

        #ethtool -s eth? speed SPEED_MODE duplex DUPLEX_MODE autoneg NWAY_OPTION

        ,where
                SPEED_MODE        = 1000        for 1000Mbps
                                = 100        for 100Mbps
                                = 10        for 10Mbps
                DUPLEX_MODE        = half        for half-duplex
                                = full        for full-duplex
                NWAY_OPTION        = off        for auto-negotiation off
                                = on        for auto-negotiation on

=====================================================

前面make clean modules，make install，depmod -a这三步都没问题，没有得到错误提示，但装后没有任何反应，在网络配制里也没有显示任何网络设备。重启也没有。
然后想做#insmod这一步，却无论如何找不到~/r1000这个目录，命令打下去当然也是出错。我是新手，怎么想也想不通我已经完全按照说明书做了却怎么还不行。不知道是不是这个驱动有问题。请大家帮帮忙！谢谢！

meaning

自己顶一下
有人知道吗？