|
|
我在F7下用ircd-hybrid做一个IRC，可以运行，我的IP地址是：192.168.145.174
但我在自己的机器上用irssi用/connect 192.168.145.174命令登陆，然后我用/list命令，但出现下面的信息：
21:19 -!- Irssi: Not connected to server
完整登陆信息如下：
21:20 -!- Irssi: Looking up 192.168.145.174
21:20 -!- Irssi: Connecting to 192.168.145.174 [192.168.145.174] port 6667
21:20 -!- Irssi: Connection to 192.168.145.174 established
21:20 -!- World NOTICE AUTH :*** Looking up your hostname...
21:20 -!- World NOTICE AUTH :*** Couldn't look up your hostname
21:20 -!- World 001 heavens :Welcome to the Our Net Internet Relay Chat Network
heavens
21:20 -!- World 002 heavens :Your host is Our World[0.0.0.0/6667], running
version hybrid-7.2.3
21:20 -!- World 003 heavens :This server was created May 5 2007 at 14:15:58
21:20 -!- World 004 heavens Our World hybrid-7.2.3 CDGabcdfgiklnorsuwxyz
biklmnopstveI bkloveI
21:20 -!- World 005 heavens CALLERID CASEMAPPING=rfc1459 DEAF=D KICKLEN=160
MODES=4 NICKLEN=51 PREFIX=(ov)@+ STATUSMSG=@+ TOPICLEN=120
NETWORK=Our Net MAXLIST=beI:25 MAXTARGETS=4 CHANTYPES=#& :are
supported by this server
21:20 -!- World 005 heavens CHANLIMIT=#&:25 CHANNELLEN=50 EXCEPTS=e INVEX=I
CHANMODES=eIb,k,l,imnpst KNOCK ELIST=CMNTU SAFELIST AWAYLEN=160 :are
supported by this server
21:20 -!- World 042 heavens 9ZZAAAAAG :your unique ID
21:20 -!- World 251 heavens :There are 0 users and 1 invisible on 1 servers
21:20 -!- World 255 heavens :I have 1 clients and 0 servers
21:20 -!- World 265 heavens :Current local users: 1 Max: 2
21:20 -!- World 266 heavens :Current global users: 1 Max: 2
21:20 -!- World 250 heavens :Highest connection count: 2 (2 clients) (7
connections received)
21:20 !192.168.145.174 *** Notice -- motd was last changed at 6/5/2007 2:16
21:20 !192.168.145.174 *** Notice -- Please read the motd if you haven't read it
21:20 -!- World 375 heavens :- Our World Message of the Day -
21:20 -!- World 372 heavens :- *** This is the short motd ***
21:20 -!- World 376 heavens :End of /MOTD command.
21:20 -!- Mode change [+i] for user heavens
21:20 -!- Irssi: Not connected to server
配置文件ircd.conf如下：
/* doc/example.conf - ircd-hybrid-7 Example configuration file
* Copyright (C) 2000-2006 Hybrid Development Team
*
* Written by ejb, wcampbel, db, leeh and others
* Other example configurations can be found in the source dir under
* etc/.
*
* $Id: example.conf 853 2007-02-22 06:01:30Z db $
*/
/* IMPORTANT NOTES:
*
* auth {} blocks MUST be specified in order of precedence. The first one
* that matches a user will be used. So place spoofs first, then specials,
* then general access.
*
* Shell style (#), C++ style (//) and C style comments are supported.
*
* Files may be included by either:
* .include "filename"
* .include <filename>
*
* Times/durations are written as:
* 12 hours 30 minutes 1 second
*
* Valid units of time:
* month, week, day, hour, minute, second
*
* Valid units of size:
* megabyte/mbyte/mb, kilobyte/kbyte/kb, byte
*
* Sizes and times may be singular or plural.
*/
/* EFNET NOTE:
*
* This config file is NOT suitable for EFNet. EFNet admins should use
* example.efnet.conf
*/
/*
* serverinfo {}: contains information about the server. (OLD M
*/
serverinfo {
/*
* name: the name of our server. This cannot be changed at runtime.
*/
name = "Our World";
/*
* sid: a server's unique ID. This is three characters long and must
* be in the form [0-9][A-Z0-9][A-Z0-9]. The first character must be
* a digit, followed by 2 alpha-numerical letters.
* NOTE: The letters must be capitalized. This cannot be changed at runtime.
*/
sid = "9ZZ";
/*
* description: the description of the server. '[' and ']' may not
* be used here for compatibility with older servers.
*/
description = "ABC server";
/*
* network info: the name and description of the network this server
* is on. Shown in the 005 reply and used with serverhiding.
*/
network_name = "Our Net";
network_desc = "This is Our Network";
/*
* hub: allow this server to act as a hub and have multiple servers
* connected to it. This may not be changed if there are active
* LazyLink servers.
*/
hub = no;
/*
* vhost: the IP to bind to when we connect outward to ipv4 servers.
* This should be an ipv4 IP only, or "* for INADDR_ANY.
*/
#vhost = "192.169.0.1";
/*
* vhost6: the IP to bind to when we connect outward to ipv6 servers.
* This should be an ipv6 IP only, or "* for INADDR_ANY.
*/
#vhost6 = "3ffe:80e8:546::2";
/* max_clients: the maximum number of clients allowed to connect */
max_clients = 512;
/*
* rsa key: the path to the file containing our rsa key for cryptlink.
*
* Example command to store a 2048 bit RSA keypair in
* rsa.key, and the public key in rsa.pub:
*
* openssl genrsa -out rsa.key 2048
* openssl rsa -in rsa.key -pubout -out rsa.pub
* chown <ircd-user>.<ircd.group> rsa.key rsa.pub
* chmod 0600 rsa.key
* chmod 0644 rsa.pub
*/
#rsa_private_key_file = "/usr/local/ircd/etc/rsa.key";
/*
* ssl certificate: the path to the file containing our ssl certificate
* for encrypted client connection.
*
* This assumes your private RSA key is stored in rsa.key. You
* MUST have an RSA key in order to generate the certificate
*
* openssl req -new -days 365 -x509 -key rsa.key -out cert.pem
*
* See http://www.openssl.org/docs/HOWTO/certificates.txt
*
* Please use the following values when generating the cert
*
* Organization Name: Network Name
* Organization Unit Name: changme.someirc.net
* Common Name: irc.someirc.net
* E-mail: you@domain.com
*/
#ssl_certificate_file = "/usr/local/ircd/etc/cert.pem";
};
/*
* admin {}: contains admin information about the server. (OLD A
*/
admin {
name = "Smurf target";
description = "Main Server Administrator";
email = "<syn@packets.r.us>";
};
/*
* log {}: contains information about logfiles.
*/
log {
/* Do you want to enable logging to ircd.log? */
use_logging = yes;
/*
* logfiles: the logfiles to use for user connects, /oper uses,
* and failed /oper. These files must exist for logging to be used.
*/
fname_userlog = "logs/userlog";
fname_operlog = "logs/operlog";
fname_killlog = "logs/kill";
fname_klinelog = "logs/kline";
fname_glinelog = "logs/gline";
/*
* log_level: the amount of detail to log in ircd.log. The
* higher, the more information is logged. May be changed
* once the server is running via /quote SET LOG. Either:
* L_CRIT, L_ERROR, L_WARN, L_NOTICE, L_TRACE, L_INFO or L_DEBUG
*/
log_level = L_INFO;
};
/*
* class {}: contains information about classes for users (OLD Y
*/
class {
/* name: the name of the class. classes are text now */
name = "users";
/*
* ping_time: how often a client must reply to a PING from the
* server before they are dropped.
*/
ping_time = 90 seconds;
/*
* number_per_ip: how many local users are allowed to connect
* from one IP (optional)
*/
number_per_ip = 2;
/*
* max_local: how many local users are allowed to connect
* from one ident@host (optional)
*/
max_local = 2;
/*
* max_global: network-wide limit of users per ident@host (optional)
*/
max_global = 10;
/*
* max_number: the maximum number of users allowed in this class (optional)
*/
max_number = 100;
/*
* the following lines are optional and allow you to define
* how many users can connect from one /NN subnet
*/
cidr_bitlen_ipv4 = 24;
cidr_bitlen_ipv6 = 120;
number_per_cidr = 16;
/*
* sendq: the amount of data allowed in a clients queue before
* they are dropped.
*/
sendq = 100 kbytes;
};
class {
name = "users";
ping_time = 2 minutes;
number_per_ip = 2;
max_number = 512;
sendq = 100kbytes;
};
class {
name = "server";
ping_time = 90 seconds;
/*
* ping_warning: how fast a server must reply to a PING before
* a warning to opers is generated.
*/
ping_warning = 15 seconds;
/*
* connectfreq: only used in server classes. Specifies the delay
* between autoconnecting to servers.
*/
connectfreq = 5 minutes;
/* max number: the amount of servers to autoconnect to */
max_number = 1;
/* sendq: servers need a higher sendq as they send more data */
sendq = 2 megabytes;
};
/*
* listen {}: contains information about the ports ircd listens on (OLD P
*/
listen {
/*
* port: the specific port to listen on. If no host is specified
* before, it will listen on all available IPs.
*
* Ports are separated via a comma, a range may be specified using ".."
*/
/* port: listen on all available IPs, ports 6665 to 6669 */
#port = 6665 .. 6669;
port = 6667;
/*
* Listen on 192.168.0.1/6697 with ssl enabled and hidden from STATS P
* unless you are an administrator.
*
* NOTE: The "flags" directive has to come before "port". Always!
*/
flags = hidden, ssl;
host = "192.168.145.174";
port = 6667;
/*
* host: set a specific IP/host the ports after the line will listen
* on. This may be ipv4 or ipv6.
*/
host = "192.168.145.174";
port = 7000, 7001;
#host = "3ffe:1234:a:b:c::d";
#port = 7002;
};
/*
* auth {}: allow users to connect to the ircd (OLD I
*/
auth {
/*
* user: the user@host allowed to connect. Multiple IPv4/IPv6 user
* lines are permitted per auth block.
*/
user = "*@172.16.0.0/12";
user = "*test@123D:B567:*";
/* password: an optional password that is required to use this block */
password = "86712536";
/*
* encrypted: controls whether the auth password above has been
* encrypted.
*/
encrypted = yes;
/*
* spoof: fake the users host to this. This is free-form,
* just do everyone a favor and don't abuse it. ('=' prefix on /stats I)
*/
spoof = "I.still.hate.packets";
/* class: the class the user is placed in */
class = "opers";
/*
* need_password: don't allow users who haven't supplied the correct
* password to connect using another auth{} block
* ('&' prefix on /stats I if disabled)
* need_ident: require the user to have identd to connect ('+' prefix on /stats I)
* spoof_notice: enable spoofing notification to admins
* exceed_limit: allow a user to exceed class limits ('>' prefix on /stats I)
* kline_exempt: exempt this user from k/glines ('^' prefix on /stats I)
* gline_exempt: exempt this user from glines ('_' prefix on /stats I)
* resv_exempt: exempt this user from resvs ('$' prefix on /stats I)
* no_tilde: remove ~ from a user with no ident ('-' prefix on /stats I)
* can_flood: allow this user to exceed flood limits ('|' prefix on /stats I)
* can_idle: exempt this user from idle restrictions ('<' prefix on /stats I)
*/
flags = need_password, spoof_notice, exceed_limit, kline_exempt,
gline_exempt, resv_exempt, no_tilde, can_flood, can_idle;
};
auth {
/*
* redirect: the server and port to redirect a user to. A user does
* not have to obey the redirection, the ircd just suggests an alternative
* server for them.
*/
redirserv = "this.is.not.a.real.server";
redirport = 6667;
user = "*.server";
/* class: a class is required even though it is not used */
class = "users";
};
auth {
user = "*@*";
class = "users";
#flags = need_ident;
};
/*
* operator {}: defines ircd operators. (OLD O
*
* ircd-hybrid no longer supports local operators, privileges are
* controlled via flags.
*/
operator {
/* name: the name of the oper */
/* NOTE: operator "opername"{} is also supported */
name = "heavens";
/*
* user: the user@host required for this operator. CIDR is not
* supported. Multiple user="" lines are supported.
*/
user = "*heavens@*";
user = "*@127.0.0.1";
/*
* password: the password required to oper. By default this will
* need to be encrypted using 'mkpasswd'. MD5 is supported.
*/
password = "86712536";
/*
* encrypted: controls whether the oper password above has been
* encrypted. (OLD CRYPT_OPER_PASSWORD now optional per operator)
*/
encrypted = yes;
/*
* rsa_public_key_file: the public key for this oper when using Challenge.
* A password should not be defined when this is used, see
* doc/challenge.txt for more information.
*/
# rsa_public_key_file = "/usr/local/ircd/etc/oper.pub";
/* class: the class the oper joins when they successfully /oper */
class = "opers";
/*
* umodes: default usermodes opers get when they /oper. If defined,
* it will override oper_umodes settings in general {}.
* Available usermodes:
*
* +b - bots - See bot and drone flooding notices
* +c - cconn - Client connection/quit notices
* +D - deaf - Don't receive channel messages
* +d - debug - See debugging notices
* +f - full - See I: line full notices
* +G - softcallerid - Server Side Ignore for users not on your channels
* +g - callerid - Server Side Ignore (for privmsgs etc)
* +i - invisible - Not shown in NAMES or WHO unless you share a
* a channel
* +k - skill - See server generated KILL messages
* +l - locops - See LOCOPS messages
* +n - nchange - See client nick changes
* +r - rej - See rejected client notices
* +s - servnotice - See general server notices
* +u - unauth - See unauthorized client notices
* +w - wallop - See server generated WALLOPS
* +x - external - See remote server connection and split notices
* +y - spy - See LINKS, STATS, TRACE notices etc.
* +z - operwall - See oper generated WALLOPS
*/
# umodes = locops, servnotice, operwall, wallop;
/*
* privileges: controls the activities and commands an oper is
* allowed to do on the server. All options default to no.
* Available options:
*
* global_kill: allows remote users to be /KILL'd (OLD 'O' flag)
* remote: allows remote SQUIT and CONNECT (OLD 'R' flag)
* remoteban: allows remote KLINE/UNKLINE
* kline: allows KILL, KLINE and DLINE (OLD 'K' flag)
* unkline: allows UNKLINE and UNDLINE (OLD 'U' flag)
* gline: allows GLINE (OLD 'G' flag)
* xline: allows XLINE (OLD 'X' flag)
* operwall: allows OPERWALL
* nick_changes: allows oper to see nickchanges (OLD 'N' flag)
* via usermode +n
* rehash: allows oper to REHASH config (OLD 'H' flag)
* die: allows DIE and RESTART (OLD 'D' flag)
* admin: gives admin privileges. admins
* may (un)load modules and see the
* real IPs of servers.
* hidden_admin: same as 'admin', but noone can recognize you as
* being an admin
* hidden_oper: not shown in /stats p (except for other operators)
*/
/* You can either use
* die = yes;
* rehash = yes;
*
* or in a flags statement i.e.
* flags = die, rehash;
*
* You can also negate a flag with ~ i.e.
* flags = ~remote;
*
*/
flags = global_kill, remote, kline, unkline, xline,
die, rehash, nick_changes, admin, operwall;
};
/*
* connect {}: controls servers we connect to (OLD C:, N:, H:, L
*/
connect {
/* name: the name of the server */
#name = "irc.uplink.com";
/*
* host: the host or IP to connect to. If a hostname is used it
* must match the reverse dns of the server.
*/
host = "192.168.145.174";
/*
* vhost: the IP to bind to when we connect outward to servers.
* serverinfo::vhost and serverinfo::vhost6 will be overridden
* by this directive.
*/
vhost = "192.168.145.174";
/*
* passwords: the passwords we send (OLD C and accept (OLD N.
* The remote server will have these passwords reversed.
*/
send_password = "password";
accept_password = "anotherpassword";
/*
* encrypted: controls whether the accept_password above has been
* encrypted. (OLD CRYPT_LINK_PASSWORD now optional per connect)
*/
encrypted = no;
/* port: the port to connect to this server on */
port = 6667;
/*
* hub_mask: the mask of servers that this server may hub. Multiple
* entries are permitted
*/
hub_mask = "*";
/*
* leaf_mask: the mask of servers this server may not hub. Multiple
* entries are permitted. Useful for forbidding EU -> US -> EU routes.
*/
# leaf_mask = "*.uk";
/* fakename: the servername we pretend to be when we connect */
# fakename = "*.arpa";
/* class: the class this server is in */
class = "server";
/*
* autoconn: controls whether we autoconnect to this server or not,
* dependent on class limits. By default, this is disabled.
* compressed: controls whether traffic is compressed via ziplinks.
* By default, this is disabled
* lazylink: controls whether this server is a LazyLink. LazyLink
* servers may NOT hub. See doc/LazyLinks.txt
* cryptlink: enable full encryption for all data passing between our
* server and this link and rsa authentication.
* burst_away: This will send the /away string that users have set
* on the server burst. Note this can be a lot of data
* and slow down your server burst.
* topicburst: Send topics to this server during channel burst. Works
* only if the server we are connecting to is capable
* of TBURST/TB.
*/
# flags = autoconn, lazylink, compressed, cryptlink, burst_away, topicburst;
};
connect {
#name = "encrypted.auth.example";
host = "192.168.145.174";
port = 6667;
flags = cryptlink;
/*
* rsa_public_key_file: the path to the public keyfile of the server.
* Used instead of passwords.
*/
rsa_public_key_file = "etc/remote.server.keyfile";
/*
* cipher preference: set the preferred cipher for this link
*
* Available ciphers are:
* BF/168 BF/128 CAST/128 IDEA/128 RC5.16/128
* RC5.12/128 RC5.8/128 3DES/168 DES/56
*
* NOTE: Some ciphers may not be supported by your OpenSSL.
* Check the output from 'configure' for available ciphers.
*
* NOTE2: To help you decide what cipher to use, tools/encspeed
* will show you approximately how fast each cipher is.
* However, blowfish is fast and secure, and is probably
* a good default for most situations.
*
* NOTE3: Default if none is set is BF/128
*
* The cipher *MUST* be the same in both directions. If you
* set a cipher preference, your uplink must set the same cipher,
* else it will not link.
*/
# cipher_preference = "BF/168";
};
/*
* NOTE: Don't add an extra 'name=' entry if you use
* the connect "name"{} feature
*/
connect "ipv6.some.server" {
host = "3ffd:dead:beef::1";
send_password = "password";
accept_password = "password";
port = 6666;
/*
* aftype: controls whether the connection uses "ipv4" or "ipv6".
* Default is ipv4.
*/
aftype = ipv6;
class = "server";
};
/*
* cluster {}: servers that share klines/unkline/xline/unxline/resv/unresv/locops
* automatically (OLD hyb6 SLAVE_SERVERS)
*/
cluster {
/*
* name: the server to share with, this can take wildcards
*
* NOTE: only local actions will be clustered, meaning if
* the server receives a shared kline/unkline/etc, it
* will not be propagated to clustered servers.
*
* Remote servers are not necessarily required to accept
* clustered lines, they need a shared{} for *THIS* server
* in order to accept them.
*/
name = "*.arpa";
/*
* type: list of what to share, options are as follows:
* kline - share klines
* tkline - share temporary klines
* unkline - share unklines
* xline - share xlines
* txline - share temporary xlines
* unxline - share unxlines
* resv - share resvs
* tresv - share temporary resvs
* unresv - share unresvs
* locops - share locops
* all - share all of the above (default)
*/
type = kline, unkline, locops, xline, resv;
};
/*
* shared {}: users that are allowed to remote kline (OLD U
*
* NOTE: This can be effectively used for remote klines.
* Please note that there is no password authentication
* for users setting remote klines. You must also be
* /oper'd in order to issue a remote kline.
*/
shared {
/*
* name: the server the user must be on to set klines. If this is not
* specified, the user will be allowed to kline from all servers.
*/
name = "irc2.some.server";
/*
* user: the user@host mask that is allowed to set klines. If this is
* not specified, all users on the server above will be allowed to set
* a remote kline.
*/
user = "oper@my.host.is.spoofed";
/*
* type: list of what to share, options are as follows:
* kline - allow oper/server to kline
* tkline - allow temporary klines
* unkline - allow oper/server to unkline
* xline - allow oper/server to xline
* txline - allow temporary xlines
* unxline - allow oper/server to unxline
* resv - allow oper/server to resv
* tresv - allow temporary resvs
* unresv - allow oper/server to unresv
* locops - allow oper/server to locops - only used for servers that cluster
* all - allow oper/server to do all of the above (default)
*/
type = kline, unkline, resv;
};
/*
* kill {}: users that are not allowed to connect (OLD K:)
* Oper issued klines will be added to the specified kline config
*/
kill {
user = "bad@*.hacked.edu";
reason = "Obviously hacked account";
};
kill {
user = "^O[[:alpha:]]?[[:digit:]]+(x\.o|\.xo)$@^[[:alnum:]]{4}\.evilnet.org$";
type = regex;
};
/*
* deny {}: IPs that are not allowed to connect (before DNS/ident lookup)
* Oper issued dlines will be added to the specified dline config
*/
deny {
ip = "10.0.1.0/24";
reason = "Reconnecting vhosted bots";
};
/*
* exempt {}: IPs that are exempt from deny {} and Dlines. (OLD d:)
*/
exempt {
ip = "192.168.0.0/16";
};
/*
* resv {}: nicks and channels users may not use/join (OLD Q:)
*/
resv {
/* reason: the reason for the proceeding resv's */
reason = "There are no services on this network";
/* resv: the nicks and channels users may not join/use */
nick = "nickserv";
nick = "chanserv";
channel = "#services";
/* resv: wildcard masks are also supported in nicks only */
reason = "Clone bots";
nick = "clone*";
};
/*
* gecos {}: The X: replacement, used for banning users based on
* their "realname".
*/
gecos {
name = "*sex*";
reason = " ossible spambot";
};
gecos {
name = "sub7server";
reason = "Trojan drone";
};
gecos {
name = "*http*";
reason = "Spambot";
};
gecos {
name = "^\[J[0o]hn Do[3e]\]-[0-9]{2,5}$";
type = regex;
};
/*
* channel {}: The channel block contains options pertaining to channels
*/
channel {
/*
* disable_fake_channels: this option, if set to 'yes', will
* disallow clients to create or join channels that have one
* of the following ASCII characters in their name:
*
* 2 | bold
* 3 | mirc color
* 15 | plain text
* 22 | reverse
* 31 | underline
* 160 | non-breaking space
*/
disable_fake_channels = no;
/*
* restrict_channels: reverse channel RESVs logic, only reserved
* channels are allowed
*/
restrict_channels = no;
/*
* disable_local_channels: prevent users from joining &channels.
*/
disable_local_channels = no;
/*
* use_invex: Enable/disable channel mode +I, a n!u@h list of masks
* that can join a +i channel without an invite.
*/
use_invex = yes;
/*
* use_except: Enable/disable channel mode +e, a n!u@h list of masks
* that can join a channel through a ban (+b).
*/
use_except = yes;
/*
* use_knock: Allows users to request an invite to a channel that
* is locked somehow (+ikl). If the channel is +p or you are banned
* the knock will not be sent.
*/
use_knock = yes;
/*
* knock_delay: The amount of time a user must wait between issuing
* the knock command.
*/
knock_delay = 1 minutes;
/*
* knock_delay_channel: How often a knock to any specific channel
* is permitted, regardless of the user sending the knock.
*/
knock_delay_channel = 1 minute;
/*
* burst_topicwho: enable sending of who set topic on topicburst
* default is yes
*/
burst_topicwho = yes;
/*
* max_chans_per_user: The maximum number of channels a user can
* join/be on.
*/
max_chans_per_user = 25;
/* quiet_on_ban: stop banned people talking in channels. */
quiet_on_ban = yes;
/* max_bans: maximum number of +b/e/I modes in a channel */
max_bans = 25;
/*
* how many joins in how many seconds constitute a flood, use 0 to
* disable. +b opers will be notified (changeable via /set)
*/
join_flood_count = 16;
join_flood_time = 8 seconds;
/*
* splitcode: The ircd will now check splitmode every few seconds.
*
* Either split users or split servers can activate splitmode, but
* both conditions must be met for the ircd to deactivate splitmode.
*
* You may force splitmode to be permanent by /quote set splitmode on
*/
/*
* default_split_user_count: when the usercount is lower than this level,
* consider ourselves split. This must be set for automatic splitmode.
*/
default_split_user_count = 0;
/*
* default_split_server_count: when the servercount is lower than this,
* consider ourselves split. This must be set for automatic splitmode.
*/
default_split_server_count = 0;
/* split no create: disallow users creating channels on split. */
no_create_on_split = yes;
/* split: no join: disallow users joining channels at all on a split */
no_join_on_split = no;
};
/*
* serverhide {}: The serverhide block contains the options regarding
* serverhiding
*/
serverhide {
/*
* flatten_links: this option will show all servers in /links appear
* that they are linked to this current server
*/
flatten_links = no;
/*
* links_delay: how often to update the links file when it is
* flattened.
*/
links_delay = 5 minutes;
/*
* hidden: hide this server from a /links output on servers that
* support it. This allows hub servers to be hidden etc.
*/
hidden = no;
/*
* disable_hidden: prevent servers hiding themselves from a
* /links output.
*/
disable_hidden = no;
/*
* hide_servers: hide remote servernames everywhere and instead use
* hidden_name and network_desc.
*/
hide_servers = no;
/*
* Use this as the servername users see if hide_servers = yes.
*/
hidden_name = "*.hidden.com";
/*
* hide_server_ips: If this is disabled, opers will be unable to see servers
* ips and will be shown a masked ip, admins will be shown the real ip.
*
* If this is enabled, nobody can see a servers ip. *This is a kludge*, it
* has the side effect of hiding the ips everywhere, including logfiles.
*
* We recommend you leave this disabled, and just take care with who you
* give admin=yes; to.
*/
hide_server_ips = no;
};
/*
* general {}: The general block contains many of the options that were once
* compiled in options in config.h. The general block is read at start time.
*/
general {
/*
* gline_min_cidr: the minimum required length of a CIDR bitmask
* for IPv4 based glines
*/
gline_min_cidr = 16;
/*
* gline_min_cidr6: the minimum required length of a CIDR bitmask
* for IPv6 based glines
*/
gline_min_cidr6 = 48;
/*
* Whether to automatically set mode +i on connecting users.
*/
invisible_on_connect = yes;
/*
* If you don't explicitly specify burst_away in your connect blocks, then
* they will default to the burst_away value below.
*/
burst_away = no;
/*
* Show "actually using host <ip>" on /whois when possible.
*/
use_whois_actually = yes;
/*
* Max time from the nickname change that still causes KILL
* automatically to switch for the current nick of that user. (seconds)
*/
kill_chase_time_limit = 90;
/*
* If hide_spoof_ips is disabled, opers will be allowed to see the real IP of spoofed
* users in /trace etc. If this is defined they will be shown a masked IP.
*/
hide_spoof_ips = yes;
/*
* Ignore bogus timestamps from other servers. Yes, this will desync
* the network, but it will allow chanops to resync with a valid non TS 0
*
* This should be enabled network wide, or not at all.
*/
ignore_bogus_ts = no;
/*
* disable_auth: completely disable ident lookups; if you enable this,
* be careful of what you set need_ident to in your auth {} blocks
*/
disable_auth = yes;
/* disable_remote_commands: disable users doing commands on remote servers */
disable_remote_commands = no;
/*
* tkline_expire_notices: enables or disables temporary kline/xline
* expire notices.
*/
tkline_expire_notices = no;
/*
* default_floodcount: the default value of floodcount that is configurable
* via /quote set floodcount. This is the amount of lines a user
* may send to any other user/channel in one second.
*/
default_floodcount = 10;
/*
* failed_oper_notice: send a notice to all opers on the server when
* someone tries to OPER and uses the wrong password, host or ident.
*/
failed_oper_notice = yes;
/*
* dots_in_ident: the amount of '.' characters permitted in an ident
* reply before the user is rejected.
*/
dots_in_ident = 2;
/*
* dot_in_ip6_addr: ircd-hybrid-6.0 and earlier will disallow hosts
* without a '.' in them. This will add one to the end. Only needed
* for older servers.
*/
dot_in_ip6_addr = no;
/*
* min_nonwildcard: the minimum non wildcard characters in k/d/g lines
* placed via the server. klines hand placed are exempt from limits.
* wildcard chars: '.' ':' '*' '?' '@' '!' '#'
*/
min_nonwildcard = 4;
/*
* min_nonwildcard_simple: the minimum non wildcard characters in
* gecos bans. wildcard chars: '*' '?' '#'
*/
min_nonwildcard_simple = 3;
/* max_accept: maximum allowed /accept's for +g usermode */
max_accept = 20;
/* anti_nick_flood: enable the nickflood control code */
anti_nick_flood = yes;
/* nick flood: the nick changes allowed in the specified period */
max_nick_time = 20 seconds;
max_nick_changes = 5;
/*
* anti_spam_exit_message_time: the minimum time a user must be connected
* before custom quit messages are allowed.
*/
anti_spam_exit_message_time = 5 minutes;
/*
* ts delta: the time delta allowed between server clocks before
* a warning is given, or before the link is dropped. all servers
* should run ntpdate/rdate to keep clocks in sync
*/
ts_warn_delta = 30 seconds;
ts_max_delta = 5 minutes;
/*
* kline_with_reason: show the user the reason why they are k/d/glined
* on exit. May give away who set k/dline when set via tcm.
*/
kline_with_reason = yes;
/*
* kline_reason: show this message to users on channel
* instead of the oper reason.
*/
kline_reason = "Connection closed";
/*
* reject_hold_time: wait this amount of time before disconnecting
* a rejected client. Use 0 to disable.
*/
reject_hold_time = 0;
/*
* warn_no_nline: warn opers about servers that try to connect but
* we don't have a connect {} block for. Twits with misconfigured
* servers can get really annoying with this enabled.
*/
warn_no_nline = yes;
/*
* stats_e_disabled: set this to 'yes' to disable "STATS e" for both
* operators and administrators. Doing so is a good idea in case
* there are any exempted (exempt{}) server IPs you don't want to
* see leaked.
*/
stats_e_disabled = no;
/* stats_o_oper only: make stats o (opers) oper only */
stats_o_oper_only = yes;
/* stats_P_oper_only: make stats P (ports) oper only */
stats_P_oper_only = yes;
/*
* stats i oper only: make stats i (auth {}) oper only. set to:
* yes: show users no auth blocks, made oper only.
* masked: show users first matching auth block
* no: show users all auth blocks.
*/
stats_i_oper_only = yes;
/*
* stats_k_oper_only: make stats k/K (klines) oper only. set to:
* yes: show users no auth blocks, made oper only
* masked: show users first matching auth block
* no: show users all auth blocks.
*/
stats_k_oper_only = yes;
/*
* caller_id_wait: time between notifying a +g user that somebody
* is messaging them.
*/
caller_id_wait = 1 minute;
/*
* opers_bypass_callerid: allows operators to bypass +g and message
* anyone who has it set (useful if you use services).
*/
opers_bypass_callerid = no;
/*
* pace_wait_simple: time between use of less intensive commands
* (ADMIN, HELP, (L)USERS, VERSION, remote WHOIS)
*/
pace_wait_simple = 60 second;
/*
* pace_wait: time between more intensive commands
* (INFO, LINKS, LIST, MAP, MOTD, STATS, WHO, wildcard WHOIS, WHOWAS)
*/
pace_wait = 70 seconds;
/*
* short_motd: send clients a notice telling them to read the motd
* instead of forcing a motd to clients who may simply ignore it.
*/
short_motd = yes;
/*
* ping_cookie: require clients to respond exactly to a ping command,
* can help block certain types of drones and FTP PASV mode spoofing.
*/
ping_cookie = no;
/* no_oper_flood: increase flood limits for opers. */
no_oper_flood = yes;
/*
* true_no_oper_flood: completely eliminate flood limits for opers
* and for clients with can_flood = yes in their auth {} blocks
*/
true_no_oper_flood = yes;
/* oper_pass_resv: allow opers to over-ride RESVs on nicks/channels */
oper_pass_resv = yes;
/*
* idletime: the maximum amount of time a user may idle before
* they are disconnected
*/
idletime = 0;
/* REMOVE ME. The following line checks you've been reading. */
havent_read_conf = 0;
/*
* max_targets: the maximum amount of targets in a single
* PRIVMSG/NOTICE. Set to 999 NOT 0 for unlimited.
*/
max_targets = 4;
/*
* client_flood: maximum amount of data in a clients queue before
* they are dropped for flooding.
*/
client_flood = 2560 bytes;
/*
* message_locale: the default message locale
* Use "standard" for the compiled in defaults.
* To install the translated messages, go into messages/ in the
* source directory and run `make install'.
*/
message_locale = "standard";
/*
* usermodes configurable: a list of usermodes for the options below
*
* +b - bots - See bot and drone flooding notices
* +c - cconn - Client connection/quit notices
* +D - deaf - Don't receive channel messages
* +d - debug - See debugging notices
* +f - full - See I: line full notices
* +G - softcallerid - Server Side Ignore for users not on your channels
* +g - callerid - Server Side Ignore (for privmsgs etc)
* +i - invisible - Not shown in NAMES or WHO unless you share a
* a channel
* +k - skill - See server generated KILL messages
* +l - locops - See LOCOPS messages
* +n - nchange - See client nick changes
* +r - rej - See rejected client notices
* +s - servnotice - See general server notices
* +u - unauth - See unauthorized client notices
* +w - wallop - See server generated WALLOPS
* +x - external - See remote server connection and split notices
* +y - spy - See LINKS, STATS, TRACE notices etc.
* +z - operwall - See oper generated WALLOPS
*/
/* oper_only_umodes: usermodes only opers may set */
oper_only_umodes = bots, cconn, cconn_full, debug, full, skill,
nchange, rej, spy, external, operwall,
locops, unauth;
/* oper_umodes: default usermodes opers get when they /oper */
oper_umodes = bots, locops, servnotice, operwall, wallop;
/*
* servlink_path: path to 'servlink' program used by ircd to handle
* encrypted/compressed server <-> server links.
*
* only define if servlink is not in same directory as ircd itself.
*/
#servlink_path = "/usr/local/ircd/bin/servlink";
/*
* default_cipher_preference: default cipher to use for cryptlink when none is
* specified in connect block.
*/
#default_cipher_preference = "BF/168";
/*
* use_egd: if your system does not have *random devices yet you
* want to use OpenSSL and encrypted links, enable this. Beware -
* EGD is *very* CPU intensive when gathering data for its pool
*/
# use_egd = yes;
/*
* egdpool_path: path to EGD pool. Not necessary for OpenSSL >= 0.9.7
* which automatically finds the path.
*/
# egdpool_path = "/var/run/egd-pool";
/*
* compression_level: level of compression for compressed links between
* servers.
*
* values are between: 1 (least compression, fastest)
* and: 9 (most compression, slowest).
*/
# compression_level = 6;
/*
* throttle_time: the minimum amount of time between connections from
* the same ip. exempt {} blocks are excluded from this throttling.
* Offers protection against flooders who reconnect quickly.
* Set to 0 to disable.
*/
throttle_time = 10;
};
glines {
/* enable: enable glines, network wide temp klines */
enable = yes;
/*
* duration: the amount of time a gline will remain on your
* server before expiring
*/
duration = 1 day;
/*
* logging: which types of rules you want to log when triggered
* (choose reject or block)
*/
logging = reject, block;
/*
* NOTE: gline ACLs can cause a desync of glines throughout the
* network, meaning some servers may have a gline triggered, and
* others may not. Also, you only need insert rules for glines
* that you want to block and/or reject. If you want to accept and
* propagate the gline, do NOT put a rule for it.
*/
/* user@host for rule to apply to */
user = "heavens@I.still.hate.packets";
/* server for rule to apply to */
name = "Our World";
/*
* action: action to take when a matching gline is found. options are:
* reject - do not apply the gline locally
* block - do not propagate the gline
*/
action = reject, block;
user = "heavens@*";
name = "*";
action = block;
};
modules {
/*
* module path: other paths to search for modules specified below
* and in /modload.
*/
path = "/usr/local/ircd/modules";
path = "/usr/local/ircd/modules/autoload";
/* module: the name of a module to load on startup/rehash */
#module = "some_module.so";
};
|
|
IP卡
狗仔卡
发表于 2007-9-2 21:15:50
提升卡
置顶卡
沉默卡
喧嚣卡
变色卡
显身卡
楼主