我的网卡被认出为eth0了, 就是连不通, 请问原因可能有/?

anguskwan

我的网卡被认出为eth0了, 就是连不通, 请问原因可能有哪些/? 谢谢`~`~:thank

anguskwan

一些配置信息如下,, 请教各位大虾!!! :help
我的芯片是VIA 的, 双PIII 1G CPU, 集成网卡,
搞了一个网上毫无结果,, 望各位大侠帮帮忙!!! 感激涕零!!! :thank :thank

/etc/network/interfaces       
### etherconf DEBCONF AREA. DO NOT EDIT THIS AREA OR INSERT TEXT BEFORE IT.
#auto lo eth0
iface lo inet loopback

auto eth0
iface eth0 inet static
        address 192.168.111.109
        netmask 255.255.255.0
        broadcast 192.168.111.255
        gateway 192.168.111.33


### END OF DEBCONF AREA.  PLACE YOUR EDITS BELOW; THEY WILL BE PRESERVED.




anguskwan:/mnt/winh# dmesg | grep eth0
eth0: VIA Rhine II at 0xe800, 00:d0:68:00:a6:33, IRQ 10.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 41e1.
eth0: Setting full-duplex based on MII #1 link partner capability of 41e1.
eth0: no IPv6 routers present
NETDEV WATCHDOG: eth0: transmit timed out  :ask
eth0: Transmit timed out, status 1003, PHY status 786d, resetting...
eth0: Setting full-duplex based on MII #1 link partner capability of 41e1.
eth0: Setting full-duplex based on MII #1 link partner capability of 41e1.
eth0: no IPv6 routers present
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timed out, status 1003, PHY status 786d, resetting...
eth0: Setting full-duplex based on MII #1 link partner capability of 41e1.
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timed out, status 1003, PHY status 786d, resetting...
eth0: Reset not complete yet. Trying harder.
eth0: Setting full-duplex based on MII #1 link partner capability of 41e1.



lspci -v
0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8653 Host Bridge
        Flags: bus master, medium devsel, latency 8
        Memory at d0000000 (32-bit, prefetchable) [size=128M]
        Capabilities: [a0] AGP version 2.0
        Capabilities: [c0] Power Management version 2

0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP] (prog-if 00 [Normal decode])
        Flags: bus master, 66MHz, medium devsel, latency 0
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
        Memory behind bridge: d8000000-daffffff
        Prefetchable memory behind bridge: db000000-dbffffff
        Capabilities: [80] Power Management version 2

0000:00:0e.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
        Subsystem: C-Media Electronics Inc CMI8738/C3DX PCI Audio Device
        Flags: bus master, medium devsel, latency 32, IRQ 5
        I/O ports at c000 [size=256]
        Capabilities: [c0] Power Management version 2

0000:00:0f.0 Unknown mass storage controller: Triones Technologies, Inc. HPT366/368/370/370A/372 (rev 04)
        Subsystem: Triones Technologies, Inc. HPT370A
        Flags: bus master, 66MHz, medium devsel, latency 120, IRQ 11
        I/O ports at c400
        I/O ports at c800
        I/O ports at cc00
        I/O ports at d000
        I/O ports at d400 [size=256]
        Capabilities: [60] Power Management version 2

0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8233 PCI to ISA Bridge
        Subsystem: VIA Technologies, Inc.: Unknown device 0000
        Flags: bus master, stepping, medium devsel, latency 0
        Capabilities: [c0] Power Management version 2

0000:00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
        Subsystem: VIA Technologies, Inc. VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE
        Flags: bus master, medium devsel, latency 32, IRQ 255
        I/O ports at d800
        Capabilities: [c0] Power Management version 2

0000:00:11.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1b) (prog-if 00 [UHCI])
        Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
        Flags: bus master, medium devsel, latency 32, IRQ 10
        I/O ports at dc00
        Capabilities: [80] Power Management version 2

0000:00:11.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1b) (prog-if 00 [UHCI])
        Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
        Flags: bus master, medium devsel, latency 32, IRQ 10
        I/O ports at e000
        Capabilities: [80] Power Management version 2

0000:00:11.4 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1b) (prog-if 00 [UHCI])
        Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
        Flags: bus master, medium devsel, latency 32, IRQ 10
        I/O ports at e400
        Capabilities: [80] Power Management version 2

0000:00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 70)
        Subsystem: VIA Technologies, Inc. VT6102 [Rhine II] Embeded Ethernet Controller on VT8235
        Flags: bus master, medium devsel, latency 32, IRQ 10
        I/O ports at e800 [size=256]
        Memory at dd000000 (32-bit, non-prefetchable) [size=256]
        Capabilities: [40] Power Management version 2

0000:01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G100 [Productiva] AGP (rev 02) (prog-if 00 [VGA])
        Subsystem: Matrox Graphics, Inc. MGA-G100 Productiva AGP
        Flags: bus master, stepping, medium devsel, latency 32, IRQ 10
        Memory at db000000 (32-bit, prefetchable) [size=16M]
        Memory at d8000000 (32-bit, non-prefetchable) [size=16K]
        Memory at d9000000 (32-bit, non-prefetchable) [size=8M]
        Capabilities: [dc] Power Management version 1
        Capabilities: [f0] AGP version 1.0

anguskwan

据说是IRQ的问题, 请问如何更改eth0的IRQ呢? 谢谢