如何安装d-link dfe-530tx 网卡?

guanhuaming · 发表于 2005-2-15 22:41:20

第一次安装使用freebsd, 请教一下如何安装d-link dfe-530tx 网卡? 我的系统是freebsd 5.3.
谢谢！

alvon · 发表于 2005-2-16 14:48:50

5.3 的认识 dfe-530的，
你输入　ifconfig 看看。
具体参看　ifconfig 的man

guanhuaming · 发表于 2005-2-16 16:29:20

谢谢alvon兄的回答。
我查了freebsd官方网站，确实5.3版认识 dfe-530。
可我安装freebsd时配置网卡的时候就是没显示出来。能请教一下你当初是怎么弄的吗?

corrs · 发表于 2005-2-17 01:42:05

当初，配置网卡的时候，应该在第一项就可以看到vr0的字样，不一定是0，但DLINK的这款肯定是vr，你选这个就OK了，如果没有看到……那么肯定是网卡松了。。。。。当然，也不排除网卡有假的可能。

guanhuaming · 发表于 2005-2-17 08:35:44

感谢corrs版主的回答。

网卡肯定没松，因为我换到windows 下就能上网了。
配置网卡的时候，我的第一项显示的是无法识别的字样。
至于网卡有假的可能性，我记得以前在linux中显示的好像是via-rhine 之类。

Eg_zm · 发表于 2005-2-17 11:09:30

请:
贴出你的dmsg
贴出你的ifconfig
linux将网卡一律认为是:eth
而bsd是不同的型号不一样.
不排除其实你的网卡不是dfe-530tx型号的.

guanhuaming · 发表于 2005-2-17 16:27:45

刚刚回房间打开FreeBSD查了一下：

1. dmesg：

------------------------------------------------------------------------------------------------------
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.3-RELEASE #2: Thu Feb 17 22:00:04 CST 2005
root@:/usr/src/sys/i386/compile/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Celeron(R) CPU 1.80GHz (2123.77-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf13 Stepping = 3
Features=0x3febfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM>
real memory = 266600448 (254 MB)
avail memory = 255418368 (243 MB)
ACPI APIC Table: <INTEL D845GVSR>
ioapic0 <Version 2.0> irqs 0-23 on motherboard
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <INTEL D845GVSR> on motherboard
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
cpu0: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <Intel 82845G (845G GMCH) SVGA controller> mem 0xffa80000-0xffafffff,0xf0000000-0xf7ffffff irq 16 at device 2.0 on pci0
agp0: detected 892k stolen memory
agp0: aperture size is 128M
uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0xe800-0xe81f irq 16 at device 29.0 on pci0
uhci0: [GIANT-LOCKED]
usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ums0: vendor 0x04fc USB Wheel Mouse, rev 1.10/1.01, addr 2, iclass 3/1
ums0: 3 buttons and Z dir.
uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0xe880-0xe89f irq 19 at device 29.1 on pci0
uhci1: [GIANT-LOCKED]
usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
umass0: Netac Netac OnlyDisk, rev 1.10/2.00, addr 2
uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0xec00-0xec1f irq 18 at device 29.2 on pci0
uhci2: [GIANT-LOCKED]
usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
pci0: <serial bus, USB> at device 29.7 (no driver attached)
pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci1: <network, ethernet> at device 1.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH4 UDMA100 controller> port 0xffa0-0xffaf,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 31.1 on pci0
ata0: channel #0 on atapci0
ata1: channel #1 on atapci0
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
pci0: <multimedia, audio> at device 31.5 (no driver attached)
acpi_button0: <Sleep Button> on acpi0
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
ppc0: <Standard parallel printer port> port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
Timecounter "TSC" frequency 2123772948 Hz quality 800
Timecounters tick every 10.000 msec
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
ad0: 39205MB <Maxtor 6E040L0/NAR61590> [79656/16/63] at ata0-master UDMA100
ad1: 39205MB <Maxtor 6E040L0/NAR61EA0> [79656/16/63] at ata0-slave UDMA100
acd0: CDRW <HL-DT-ST GCE-8526B/1.02> at ata1-master UDMA33
acd1: CDROM <ATAPI-CD ROM-DRIVE-52MAX/Ver 52F4> at ata1-slave UDMA33
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <Netac Onlydisk Popular 3.10> Fixed Direct Access SCSI-2 device
da0: 1.000MB/s transfers
da0: 30MB (62016 512 byte sectors: 64H 32S/T 30C)
Mounting root from ufs:/dev/ad0s1a
---------------------------------------------------------------------------------------------------

复制代码

2. pciconf:

--------------------------------------------------------------------------------------------------
hostb0@pci0:0:0: class=0x060000 card=0x25608086 chip=0x25608086 rev=0x01 hdr=0x00
vendor = 'Intel Corporation'
device = '82845G/GL/GV/GE/PE DRAM Controller / Host-Hub I/F Bridge'
class = bridge
subclass = HOST-PCI
agp0@pci0:2:0: class=0x030000 card=0x56418086 chip=0x25628086 rev=0x01 hdr=0x00
vendor = 'Intel Corporation'
device = '82845G/GL/GV/GE/PE Integrated Graphics Device'
class = display
subclass = VGA
uhci0@pci0:29:0: class=0x0c0300 card=0x56418086 chip=0x24c28086 rev=0x01 hdr=0x00
vendor = 'Intel Corporation'
device = '82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1'
class = serial bus
subclass = USB
uhci1@pci0:29:1: class=0x0c0300 card=0x56418086 chip=0x24c48086 rev=0x01 hdr=0x00
vendor = 'Intel Corporation'
device = '82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2'
class = serial bus
subclass = USB
uhci2@pci0:29:2: class=0x0c0300 card=0x56418086 chip=0x24c78086 rev=0x01 hdr=0x00
vendor = 'Intel Corporation'
device = '82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3'
class = serial bus
subclass = USB
none0@pci0:29:7: class=0x0c0320 card=0x56418086 chip=0x24cd8086 rev=0x01 hdr=0x00
vendor = 'Intel Corporation'
device = '82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB EHCI Controller'
class = serial bus
subclass = USB
pcib1@pci0:30:0: class=0x060400 card=0x00000000 chip=0x244e8086 rev=0x81 hdr=0x01
vendor = 'Intel Corporation'
device = '82801BA/CA/DB/DBL/EB/ER (ICH2/3/4/4-L/5/5R), 6300ESB Hub Interface to PCI Bridge'
class = bridge
subclass = PCI-PCI
isab0@pci0:31:0: class=0x060100 card=0x00000000 chip=0x24c08086 rev=0x01 hdr=0x00
vendor = 'Intel Corporation'
device = '82801DB/DBL (ICH4/ICH4-L) LPC Interface Bridge'
class = bridge
subclass = PCI-ISA
atapci0@pci0:31:1: class=0x01018a card=0x56418086 chip=0x24cb8086 rev=0x01 hdr=0x00
vendor = 'Intel Corporation'
device = '82801DB/DBL (ICH4/ICH4-L) UltraATA/100 EIDE Controller'
class = mass storage
subclass = ATA
none1@pci0:31:3: class=0x0c0500 card=0x56418086 chip=0x24c38086 rev=0x01 hdr=0x00
vendor = 'Intel Corporation'
device = '82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller'
class = serial bus
subclass = SMBus
none2@pci0:31:5: class=0x040100 card=0x02088086 chip=0x24c58086 rev=0x01 hdr=0x00
vendor = 'Intel Corporation'
device = '82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller'
class = multimedia
subclass = audio
none3@pci1:1:0: class=0x020000 card=0x08031516 chip=0x08031516 rev=0x00 hdr=0x00
vendor = 'Myson Technology Inc'
device = '803 series PCI Ethernet controller'
class = network
subclass = ethernet
---------------------------------------------------------------------------------------------------------------------

复制代码

3. ifconfig:

--------------------------------------------------------------------------------------------------------------------
plip0: flags=108810<POINTOPOINT,SIMPLEX,MULTICAST> mtu 1500
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2
--------------------------------------------------------------------------------------------------------------------

复制代码

请朋友们帮忙指点一下，谢谢！

max721 · 发表于 2005-2-18 19:45:24

pci1: <network, ethernet> at device 1.0 (no driver attached)
提示没有检测出来是什么网卡，你FreeBSD用的什么版本?
我用的也是D-LINK 530TX在 5.3 6.0都能正常使用。
你pciconf检测到的和我的不同。

none3@pci1:1:0: class=0x020000 card=0x08031516 chip=0x08031516 rev=0x00 hdr=0x00
vendor = 'Myson Technology Inc'
device = '803 series PCI Ethernet controller'
class = network
subclass = ethernet

这是我pciconf的输出

vr0@pci0:9:0: class=0x020000 card=0x14031186 chip=0x31061106 rev=0x86 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT6105M/LOM Rhine III PCI Fast Ethernet Controller'
class = network
subclass = ethernet

genym · 发表于 2005-2-18 20:51:50

我的DFE－530TX rev B也是识别不出来。

alvon · 发表于 2005-2-19 22:29:36

是不是重新编译了内核，把这个型号的网卡支持去了？

		自动登录	找回密码
密码			注册