help!!系统启动时checking new hardware 时发现hardwherehint

hillyu

[hill@localhost hill]$ dmesg
Linux version 2.4.21-0.13mdk (flepied@bi.mandrakesoft.com) (gcc version 3.2.2 (Mandrake Linux 9.1 3.2.2-3mdk)) #1 Fri Mar 14 15:08:06 EST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e5000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000007ff0000 (usable)
BIOS-e820: 0000000007ff0000 - 0000000007fffc00 (ACPI data)
BIOS-e820: 0000000007fffc00 - 0000000008000000 (ACPI NVS)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
127MB LOWMEM available.
ACPI: have wakeup address 0xc0001000
On node 0 totalpages: 32752
zone(0): 4096 pages.
zone(1): 28656 pages.
zone(2): 0 pages.
Kernel command line: auto BOOT_IMAGE=linux ro root=305 devfs=mount acpi=off
Local APIC disabled by BIOS -- reenabling.
Could not enable APIC!
Initializing CPU#0
Detected 796.467 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1589.24 BogoMIPS
Memory: 126108k/131008k available (1410k kernel code, 4512k reserved, 1118k data, 136k init, 0k highmem)
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU serial number disabled.
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU:     After generic, caps: 0383f9ff 00000000 00000000 00000000
CPU:             Common caps: 0383f9ff 00000000 00000000 00000000
CPU: Intel Pentium III (Coppermine) stepping 0a
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20030122
ACPI: Disabled via command line (acpi=off)
PCI: PCI BIOS revision 2.10 entry at 0xfd9be, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: ACPI tables contain no PCI IRQ routing entries
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router PIIX [8086/7110] at 00:07.0
PCI: Found IRQ 10 for device 00:04.0
PCI: Found IRQ 10 for device 00:0c.0
PCI: Sharing IRQ 10 with 00:06.0
PCI: Sharing IRQ 10 with 00:06.1
PCI: Sharing IRQ 10 with 00:0d.0
PCI: Cannot allocate resource region 4 of device 00:07.1
Limiting direct PCI/PCI transfers.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
PCI: Enabling device 00:06.1 (0000 -> 0003)
PCI: Found IRQ 10 for device 00:06.1
PCI: Sharing IRQ 10 with 00:06.0
PCI: Sharing IRQ 10 with 00:0c.0
PCI: Sharing IRQ 10 with 00:0d.0
Redundant entry in serial pci_table.  Please send the output of
lspci -vv, this message (115d,00d3,8086,2411)
and the manufacturer and name of serial board or modem board
to serial-pci-info@lists.sourceforge.net.
register_serial(): autoconfig failed
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 00:07.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x1070-0x1077, BIOS settings: hdaMA, hdb:pio
    ide1: BM-DMA at 0x1078-0x107f, BIOS settings: hdcMA, hdd:pio
hda: TOSHIBA MK1016GAP, ATA DISK drive
blk: queue c03cb420, I/O limit 4095Mb (mask 0xffffffff)
hdc: NEC CD-ROM DRIVE:291, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: host protected area => 1
hda: 19640880 sectors (10056 MB), CHS=1222/255/63, UDMA(33)
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 >
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 16384)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 106k freed
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
Journalled Block Device driver loaded
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Mounted devfs on /dev
Freeing unused kernel memory: 136k freed
Real Time Clock Driver v1.10e
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 15:32:56 Mar 14 2003
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 5 for device 00:07.2
usb-uhci.c: USB UHCI at I/O 0x10c0, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usbdevfs: remount parameter error
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,5), internal journal
Adding Swap: 128484k swap-space (priority -1)
hub.c: new USB device 00:07.2-1, assigned address 2
hub.c: USB hub found
hub.c: 3 ports detected
hub.c: new USB device 00:07.2-2, assigned address 3
usb.c: USB device 3 (vend/prod 0x5fe/0x7) is not claimed by any active driver.
usb.c: registered new driver hiddev
usb.c: registered new driver hid
input0: USB HID v1.00 Mouse [Cypress Sem. Cypress USB Mouse] on usb1:3.0
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
usb.c: registered new driver usb_mouse
usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
NTFS driver 2.1.1a [Flags: R/O MODULE].
NTFS volume version 3.1.
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw@saw.sw.com.sg> and others
PCI: Found IRQ 10 for device 00:06.0
PCI: Sharing IRQ 10 with 00:06.1
PCI: Sharing IRQ 10 with 00:0c.0
PCI: Sharing IRQ 10 with 00:0d.0
eth0: Intel Corp. 82557/8/9 [Ethernet Pro 100], 00:10:A4:77:27:3D, IRQ 10.
  Receiver lock-up bug exists -- enabling work-around.
  Board assembly 000695-001, Physical connectors present: RJ45
  Primary interface chip i82555 PHY #1.
  General self-test: passed.
  Serial sub-system self-test: passed.
  Internal registers self-test: passed.
  ROM checksum self-test: passed (0xdbd8681d).
  Receiver lock-up workaround activated.
inserting floppy driver for 2.4.21-0.13mdk
floppy0: no floppy controllers found
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
Linux Kernel Card Services Kernel Version
  options:  [pci] [cardbus] [pm]
PCI: Found IRQ 10 for device 00:0c.0
PCI: Sharing IRQ 10 with 00:06.0
PCI: Sharing IRQ 10 with 00:06.1
PCI: Sharing IRQ 10 with 00:0d.0
PCI: Assigned IRQ 5 for device 00:0c.1
Yenta IRQ list 0ad8, PCI irq10
Socket status: 30000006
Yenta IRQ list 0ad8, PCI irq5
Socket status: 30000006
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x378-0x37f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
PCI: Enabling device 00:04.0 (0000 -> 0001)
PCI: Found IRQ 10 for device 00:04.0
hdc: ATAPI 24X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
SCSI subsystem driver Revision: 1.00
Loading Lucent Modem Controller driver version 8.26
Detected Parameters Irq=10 BaseAddress=0x1068 ComAddress=0x0
Lucent Modem Interface driver version 8.26 (2002-11-04) with SHARE_IRQ enabled
ttyLT00 at 0x1068 (irq = 10) is a Lucent Modem