LinuxSir.cn,穿越时空的Linuxsir!

 找回密码
 注册
搜索
热搜: shell linux mysql
查看: 700|回复: 5

[已解决]系统升级后,网卡不能使用了!

[复制链接]
发表于 2010-3-3 22:28:54 | 显示全部楼层 |阅读模式
只是升级系统,没有重新编译内核

  1. 01:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
  2.         Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+
  3.         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
  4.         Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
  5.         Latency: 32 (8000ns min, 16000ns max)
  6.         Interrupt: pin A routed to IRQ 19
  7.         Region 0: I/O ports at bc00 [size=256]
  8.         Region 1: Memory at fdfff000 (32-bit, non-prefetchable) [size=256]
  9.         [virtual] Expansion ROM at fda00000 [disabled] [size=128K]
  10.         Capabilities: [50] Power Management version 2
  11.                 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
  12.                 Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
  13.         Kernel driver in use: 8139too
  14.         Kernel modules: 8139too, 8139cp

  15. 8139too                14344  0
  16. 8139cp                 12012  0
  17. mii                     2404  2 8139too,8139cp

  18. 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
  19. 8139too Fast Ethernet driver 0.9.28
  20. eth0: RealTek RTL8139 at 0xf9026000, 00:21:27:a0:35:c5, IRQ 19
  21. eth0:  Identified 8139 chip type 'RTL-8100B/8139D'

复制代码
发表于 2010-3-3 23:39:28 | 显示全部楼层
这个 看 lsmod 和 dmesg 的输出,好像认出来了吧?是不是 /etc 下的配置变了?
回复 支持 反对

使用道具 举报

 楼主| 发表于 2010-3-4 00:26:52 | 显示全部楼层
@pingz
alias ? 我的加上了啊
回复 支持 反对

使用道具 举报

 楼主| 发表于 2010-3-6 10:53:12 | 显示全部楼层
fdisk 看不到我的硬盘, 新插入移动硬盘和U盘都能识别...
直接使用 ifconfig eth0 x.x.x.x up, ifconfig lo up 能够使用网络
然后使用 /etc/init.d/net.lo start
  1. * Bringing up interface lo
  2. /etc/init.d/net.lo: line 510: _exists: command not found
  3. *   ERROR: interface lo does not exist
  4. *   Ensure that you have loaded the correct kernel module for your hardware
  5. * ERROR: net.lo failed to start
复制代码
回复 支持 反对

使用道具 举报

发表于 2010-3-6 12:47:39 | 显示全部楼层
运行 etc-update
回复 支持 反对

使用道具 举报

 楼主| 发表于 2010-3-8 14:03:59 | 显示全部楼层
@druggo
谢咯,因为太多了,一直不想升,现在配置一下是好了。
回复 支持 反对

使用道具 举报

您需要登录后才可以回帖 登录 | 注册

本版积分规则

快速回复 返回顶部 返回列表