求助modprobe usb-ohci时出错怎么办

zyzuoziji

以下为错误信息
[root@zhuyi yi]# /sbin/modprobe usb-ohci
/lib/modules/2.4.20-8/kernel/drivers/usb/usb-ohci.o: init_module: No such deviceHint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters.
      You may find more information in syslog or the output from dmesg
/lib/modules/2.4.20-8/kernel/drivers/usb/usb-ohci.o: insmod /lib/modules/2.4.20-8/kernel/drivers/usb/usb-ohci.o failed
/lib/modules/2.4.20-8/kernel/drivers/usb/usb-ohci.o: insmod usb-ohci failed

现在我想使用usb设备,包括鼠标,u盘等,可是用鼠标时加载usbmouse模块时提示load不成功,加载usb-ohci时又出现以上提示,应该怎麽改参数,怎么解决呢?是不是这个模块导致的不识别usb设备,我用
cat /proc/partitions也看不到sdx设备

versace

#modprobe usb-ohci

echofrompat

试试modprobe -a usb-ohci，如果还不行就把
#dmesg
#tail -f /var/log/message
这两个命令的输出贴上来，让大家都帮你看看。

zyzuoziji

还是不行啊
[root@zhuyi yi]# /sbin/modprobe -a usb-ohci
/lib/modules/2.4.20-8/kernel/drivers/usb/usb-ohci.o: init_module: No such deviceHint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters.
      You may find more information in syslog or the output from dmesg
/lib/modules/2.4.20-8/kernel/drivers/usb/usb-ohci.o: insmod /lib/modules/2.4.20-8/kernel/drivers/usb/usb-ohci.o failed
/lib/modules/2.4.20-8/kernel/drivers/usb/usb-ohci.o: insmod usb-ohci failed

[root@zhuyi yi]# dmesg
28 rq 6 len 18 ret -110
usb_control/bulk_msg: timeout
usbdevfs: USBDEVFS_CONTROL failed dev 2 rqt 128 rq 6 len 18 ret -110
lp: driver loaded but no devices found
ide-floppy driver 0.99.newide
hdc: ATAPI 24X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
cdrom: This disc doesn't have any tracks I recognize!
SCSI subsystem driver Revision: 1.00
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
[root@zhuyi yi]# tail -f /var/log/message
tail: /var/log/message: 没有那个文件或目录
tail: no files remaining


谢谢啦

zyzuoziji

[root@zhuyi yi]# tail /var/log/messages
May 12 13:58:05 zhuyi kernel: usb.c: USB device not accepting new address=3 (error=-110)
May 12 13:58:05 zhuyi kernel: hub.c: new USB device 00:11.2-2, assigned address
4
May 12 13:58:10 zhuyi kernel: usb_control/bulk_msg: timeout
May 12 13:58:10 zhuyi kernel: usb.c: USB device not accepting new address=4 (error=-110)
May 12 14:16:43 zhuyi kernel: hub.c: new USB device 00:11.2-2, assigned address
5
May 12 14:16:48 zhuyi kernel: usb_control/bulk_msg: timeout
May 12 14:16:48 zhuyi kernel: usb.c: USB device not accepting new address=5 (error=-110)
May 12 14:16:48 zhuyi kernel: hub.c: new USB device 00:11.2-2, assigned address
6
May 12 14:16:53 zhuyi kernel: usb_control/bulk_msg: timeout
May 12 14:16:53 zhuyi kernel: usb.c: USB device not accepting new address=6 (error=-110)

echofrompat

我怀疑你的机器已经加载了一个USB设备控制器的模块，所以不能加载usb-ohci。
也有可能acpi改变了IRQ的设置，你试试在启动时给kernel加上acpi=off的选项，看结果怎样。