测试机装了lenny以后老出现硬盘错误

yakczh

ata2.00: cmd 35/00:10:5b:73:d9/00:00:2a:00:00/e0 tag 0 dma 8192 out
Sep 25 15:33:34 localhost kernel: [89533.768206]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
Sep 25 15:33:34 localhost kernel: [89533.768259] ata2.00: status: { DRDY }
Sep 25 15:33:34 localhost kernel: [89533.768314] ata2: soft resetting link
Sep 25 15:33:34 localhost kernel: [89533.948712] ata2.00: configured for UDMA/33
Sep 25 15:33:34 localhost kernel: [89533.948725] ata2: EH complete
Sep 25 15:33:34 localhost kernel: [89533.967692] sd 1:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
Sep 25 15:33:34 localhost kernel: [89533.967692] sd 1:0:0:0: [sda] Write Protect is off
Sep 25 15:33:34 localhost kernel: [89533.967692] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
Sep 25 15:33:34 localhost kernel: [89533.967692] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Sep 25 15:34:49 localhost kernel: [89611.522627] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
Sep 25 15:34:49 localhost kernel: [89611.522689] ata2.00: cmd 35/00:18:0e:c6:1c/00:00:35:00:00/e0 tag 0 dma 12288 out
Sep 25 15:34:49 localhost kernel: [89611.522692]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
Sep 25 15:34:49 localhost kernel: [89611.522745] ata2.00: status: { DRDY }
Sep 25 15:34:49 localhost kernel: [89611.522801] ata2: soft resetting link
Sep 25 15:34:49 localhost kernel: [89611.708178] ata2.00: configured for UDMA/33
Sep 25 15:34:49 localhost kernel: [89611.708192] ata2: EH complete
Sep 25 15:34:49 localhost kernel: [89611.727199] sd 1:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
Sep 25 15:34:49 localhost kernel: [89611.727199] sd 1:0:0:0: [sda] Write Protect is off
Sep 25 15:34:49 localhost kernel: [89611.727199] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
Sep 25 15:34:49 localhost kernel: [89611.727199] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO o

fang.010.shu

重新调整分区次序；
尤其是注意/var分区的大小和位置；
就是安装时，手动分区时，那里；

yakczh

Post by fang.010.shu;2030434
重新调整分区次序；
尤其是注意/var分区的大小和位置；
就是安装时，手动分区时，那里；

硬盘500g

/var 分区在最后　大小80G

安装以后使用一段时间就出现这个问题，安装过程正常

defrag

/var大小80G纯属硬盘多了撑的。。。
2G就足够了。。。
/tmp挂载到tmpfs：

1. tmpfs        /tmp        tmpfs       defaults        0      0

复制代码

yakczh

Post by defrag;2030519
/var大小80G纯属硬盘多了撑的。。。
2G就足够了。。。
/tmp挂载到tmpfs：

1. tmpfs        /tmp        tmpfs       defaults        0      0

复制代码

var 的大小有限制吗？