请问如何在redhat9挂载插在usbhub的移动硬盘

zzzi

fdisk -l

Disk /dev/hda: 40.0 GB, 40007761920 bytes
255 heads, 63 sectors/track, 4864 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

   Device Boot    Start       End    Blocks   Id  System
/dev/hda1   *         1       637   5116671    7  HPFS/NTFS
/dev/hda2           638      4864  33953377+   f  Win95 Ext'd (LBA)
/dev/hda5           638      2549  15358108+   7  HPFS/NTFS
/dev/hda6          2550      2613    514048+  83  Linux
/dev/hda7          2614      2744   1052226   82  Linux swap
/dev/hda8          2745      4864  17028868+  83  Linux




/dev/hda2           638      4864  33953377+   f  Win95 Ext'd (LBA)

请问这句是什么意思？
我本的usb电压不够，我用一个带电源的一转四的usb hub，我应该怎么挂载我的硬盘呢？

北南南北

/dev/hda2 638 4864 33953377+ f Win95 Ext'd (LBA)

这是扩展分区；


fdisk -l /dev/sd*

看看有没有输出？

zzzi

回版主,当我把u盘插到hub上就不行了,郁闷,是不是得要hub的驱动亚

zzzi

这是扩展分区；


fdisk -l /dev/sd*

看看有没有输出？

没有显示,我是因为机器本身的usb口电压不够才用的一个usbhub(有外接电源的),当鼠标插在usbhub上,光电灯不亮,我应该怎么办呢

zzzi

[root@joe u]# dmesg |grep usb
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb.c: new USB bus registered, assigned bus number 1
usb-uhci.c: $Revision: 1.275 $ time 17:59:01 Mar 13 2003
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xbf80, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
usb-uhci.c: USB UHCI at I/O 0xbf40, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
usb-uhci.c: USB UHCI at I/O 0xbf20, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 4
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb.c: registered new driver hiddev
usb.c: registered new driver hid
usb.c: USB device not accepting new address=2 (error=-71)
usb.c: USB device not accepting new address=3 (error=-71)
input0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb3:2.0
usb.c: USB disconnect on device 00:1d.1-1 address 2
input0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb3:3.0
usb.c: USB device 4 (vend/prod 0x66f/0x8000) is not claimed by any active driver.
usb.c: registered new driver usb-storage
usb.c: USB disconnect on device 00:1d.7-1 address 4

zzzi

哪位能帮我看看马?