LinuxSir.cn,穿越时空的Linuxsir!

 找回密码
 注册
搜索
热搜: shell linux mysql
查看: 8741|回复: 9

河南网通新客户端4LINUX

[复制链接]
发表于 2005-3-30 15:05:40 | 显示全部楼层 |阅读模式
http://218.29.0.252/racer/linux/racer.tar.gz

1. 使用该客户端需要具备root权限. 并确认您的系统已经安装dhcp客户的软件包并且已经把网卡配置为动态获取ip地址的模式。确认系统安装的c共享库版本在2.3以上。

2. 安装: 将安装包解开到某个路径(用$dest_path表示,下面会引用该值,实际使用中,请替换为实际值)下即可

3. 环境变量设置: 为root用户增加一个环境变量RACERC指向该客户端的安装路径, 即$dest_path. 同时, 把$dest_path增加到root用户的PATH环境变量中.
        如果使用bash, 则修改root用户根目录下的.bash_profile文件, 增加如下语句: export RACERC=$dest_path, 把$dest_path增加到PATH=...语句中.

4. 配置: 如果需要, 请修改racer.ini文件以调整Server1和Server2的值, Server1和Server2表示服务器的ip地址, 如果只有一个服务器ip地址, 则Server1和Server2的值都设置为该ip地址值.

5. 使用方法
        客户端登录: $dest_path/racer/ecou.sh start
        查看状态:   $dest_path/racer/ecou.sh status
        客户端退出: $dest_path/racer/ecou.sh stop
       
       
       
1. It is necessary to have root privileges in order to use this client to access the network. Before getting start, confirm the dhcp client module(dhcpcd) have been installed on your Linux OS and the network interface have been set up to "Use dynamic Ip configuration ". The version of c share lib in system is more than 2.3.

2. Install: Extract the installing file to the path(denoted by $dest_path. $dest_path should be used below, and should be changed to actual value when you use it), and then it is ok.

3. Environment setting: environment variable RACERC=$dest_path should be added to root user, and $dest_path should be added to PATH environment variable of root user.

4. Configuration: Edit the file racer.ini to modify the value of Server1 and Server2. Server1 and Server2 mean the ip address of server. Server1 and Server2 should be set to one server ip if there is only one server ip address.

5. User's guide:
        Logon:                 $dest_path/racer/ecou.sh start
        Check status:         $dest_path/racer/ecou.sh status
        logoff:         $dest_path/racer/ecou.sh stop

本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有帐号?注册

x
发表于 2005-3-30 16:20:09 | 显示全部楼层
嘻嘻,虽然用不上,先顶一下,有空的时候学学你的代码
回复 支持 反对

使用道具 举报

发表于 2005-4-14 07:09:50 | 显示全部楼层
强!!!!
!!!!!!
要看看
回复 支持 反对

使用道具 举报

发表于 2005-5-20 02:53:10 | 显示全部楼层

楼主关于环境变量配置可以详细点吗

如题
楼主关于环境变量配置可以详细点吗
回复 支持 反对

使用道具 举报

发表于 2005-6-30 15:59:27 | 显示全部楼层
是啊 不会设置啊 救命啊!~
回复 支持 反对

使用道具 举报

发表于 2005-6-30 18:15:33 | 显示全部楼层
************,你完全是把说明文件发上来了
我就照这个  变量弄了一晚上没搞定
还是把所有文件复制到ROOT文件夹下才拨号
PS:昨天才装的红帽
回复 支持 反对

使用道具 举报

发表于 2006-11-18 21:54:21 | 显示全部楼层
不会用啊!
哪位来仔细说说?
回复 支持 反对

使用道具 举报

发表于 2006-11-18 21:54:35 | 显示全部楼层
不会用啊!
哪位来仔细说说?
回复 支持 反对

使用道具 举报

发表于 2006-11-18 23:38:00 | 显示全部楼层
怎么就有河南的啊?
能不能提供海南电信的啊?
嘿嘿!俺也是河南的,现在海南。
回复 支持 反对

使用道具 举报

发表于 2007-1-29 10:01:01 | 显示全部楼层
网通的改成pppoe+racer监控
老客户端没法用了
回复 支持 反对

使用道具 举报

您需要登录后才可以回帖 登录 | 注册

本版积分规则

快速回复 返回顶部 返回列表