|
|
我的LFS始终找不到以太网驱动，内核里面我几乎把所有的驱动都加入了，下面是我的dmesg信息，哪位能帮帮我：
Linux version 2.4.22 (root@lfs) (gcc version 3.3.1) #1 Thu Jul 22 13:04:49 EDT 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000006e00000 (usable)
BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
110MB LOWMEM available.
ACPI: have wakeup address 0xc0001000
On node 0 totalpages: 28160
zone(0): 4096 pages.
zone(1): 24064 pages.
zone(2): 0 pages.
ACPI: Unable to locate RSDP
Kernel command line: root=/dev/hda4 ro
Local APIC disabled by BIOS -- reenabling.
Could not enable APIC!
Initializing CPU#0
Detected 858.133 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1841.56 BogoMIPS
Memory: 106832k/112640k available (2782k kernel code, 5420k reserved, 881k data, 180k init, 0k highmem)
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After generic, caps: 0380a17b 00000000 00000000 00000000
CPU: Common caps: 0380a17b 00000000 00000000 00000000
CPU: Intel Pentium III (Coppermine) stepping 06
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: none
ACPI: Subsystem revision 20030813
PCI: Using configuration type 1
ACPI: System description tables not found
ACPI-0084: *** Error: acpi_load_tables: Could not get RSDP, AE_NOT_FOUND
ACPI-0134: *** Error: acpi_load_tables: Could not load tables: AE_NOT_FOUND
ACPI: Unable to load the System Description Tables
PCI: Probing PCI hardware
PCI: ACPI tables contain no PCI IRQ routing entries
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router PIIX [8086/7110] at 00:07.0
Limiting direct PCI/PCI transfers.
isapnp: Scanning for PnP cards...
isapnp: checksum for device 1 is not valid (0x89)
isapnp: checksum for device 2 is not valid (0xbe)
isapnp: Card 'Sound Blaster 16'
isapnp: Card 'Game Port'
isapnp: 2 Plug & Play cards detected total
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
Journalled Block Device driver loaded
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver v1.1.22 [Flags: R/O]
QNX4 filesystem 0.2.2 registered.
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ DETECT_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a TI16750
ttyS01 at 0x02f8 (irq = 3) is a TI16750
xd: Out of memory.
Floppy drive(s): fd0 is 1.44M
DOR0=4
floppy interrupt on bizarre fdc 1
handler=00000000
FDC 0 is an 82078.
eth0: D-Link DE-600 pocket adapter: not at I/O 0x378.
D-Link DE-620 pocket adapter not identified in the printer port
eth1: D-Link DE-600 pocket adapter: not at I/O 0x378.
D-Link DE-620 pocket adapter not identified in the printer port
eth2: D-Link DE-600 pocket adapter: not at I/O 0x378.
D-Link DE-620 pocket adapter not identified in the printer port
eth3: D-Link DE-600 pocket adapter: not at I/O 0x378.
D-Link DE-620 pocket adapter not identified in the printer port
eth4: D-Link DE-600 pocket adapter: not at I/O 0x378.
D-Link DE-620 pocket adapter not identified in the printer port
eth5: D-Link DE-600 pocket adapter: not at I/O 0x378.
D-Link DE-620 pocket adapter not identified in the printer port
eth6: D-Link DE-600 pocket adapter: not at I/O 0x378.
D-Link DE-620 pocket adapter not identified in the printer port
eth7: D-Link DE-600 pocket adapter: not at I/O 0x378.
D-Link DE-620 pocket adapter not identified in the printer port
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
ThunderLAN driver v1.15
TLAN: 0 devices installed, PCI: 0 EISA: 0
atp.c:v1.09 8/9/2000 Donald Becker <becker@scyld.com>
http://www.scyld.com/network/atp.html
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 76M
agpgart: no supported devices found.
[drm] Initialized tdfx 1.0.0 20010216 on minor 0
[drm] Initialized radeon 1.1.1 20010405 on minor 1
[drm:drm_init] *ERROR* Cannot initialize the agpgart module.
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 00:07.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda MA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdcMA, hdd:pio
hda: CntxCorpHD, ATA DISK drive
blk: queue c0501f80, I/O limit 4095Mb (mask 0xffffffff)
hdc: CntxCorpCD, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
hda: task_no_data_intr: error=0x04 { DriveStatusError }
hda: 33554304 sectors (17180 MB) w/64KiB Cache, CHS=2088/255/63, DMA
hdc: attached ide-cdrom driver.
hdc: ATAPI DVD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.12
Partition check:
hda: hda1 hda2 hda3 hda4
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
es1371: version v0.32 time 13:15:45 Jul 22 2004
usb.c: registered new driver hub
host/uhci.c: USB Universal Host Controller Interface driver v1.1
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
LVM version 1.0.5+(22/07/2002)
pktgen.c: v1.2: Packet Generator for packet performance testing.
pktgen: Error: your machine does not have working cycle counter.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 16384)
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
Linux IP multicast router 0.06 plus PIM-SM
ip_conntrack version 2.1 (880 buckets, 7040 max) - 292 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
NET4: Linux IPX 0.47 for NET4.0
IPX Portions Copyright (c) 1995 Caldera, Inc.
IPX Portions Copyright (c) 2000, 2001 Conectiva, Inc.
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 180k freed
Adding Swap: 192772k swap-space (priority 1)
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
偶的主系统redhat9里面识别的网卡信息是：
eth0: Digital DS21140 Tulip rev 32 at 0xc7853000, 00:03:FF:12:72:AC, IRQ 11.
难道是我没有安装module的缘故，如果是这个原因，我该怎么做呢？ |
|
IP卡
狗仔卡
发表于 2004-7-23 09:47:57
提升卡
置顶卡
沉默卡
喧嚣卡
变色卡
显身卡
楼主