请问一个启动时出错的问题

烟雨平生

系统是 Etch (Debian4.0)，一般启动都正常，突然有几次启动时出现以下信息：
..........

ata2.00: configured for UDMA/133
  Vendor: ATA       Model: ST3160811AS       Rev: 3.AA
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 312581808 5a12-byte hdwr sectors (160042 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 >
sd 1:0:0:0: Attached scsi disk sda
ide-cd: cmd 0x5a timed out
hda: lost interrupt
ide-cd: cmd 0x5a timed out
hda: lost interrupt
hda: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
hda: lost interrupt
Attempting manual resume
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
input: PC Speaker as /class/input/input1
Real Time Clock Driver v1.12ac
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
ACPI: PCI Interrupt 0000:04:01.0[A] -> GSI 17 (level, low) -> IRQ 50
PCI: Setting latency timer of device 0000:04:01.0 to 64
input: ImPS/2 Generic Wheel Mouse as /class/input/input2
ts: Compaq touchscreen protocol output
Adding 1220900k swap on /dev/sda10.  Priority:-1 extents:1 across:1220900k
EXT3 FS on sda12, internal journal
loop: loaded (max 8 devices)
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
Linux agpgart interface v0.101 (c) Dave Jones
ide-cd: cmd 0x3 timed out
hda: lost interrupt
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
[drm] Initialized drm 1.0.1 20051102
ide-cd: cmd 0x3 timed out
hda: lost interrupt
eth0: no IPv6 routers present
hda: lost interrupt
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
eth0: no IPv6 routers present
ide-cd: cmd 0x3 timed out
hda: lost interrupt
ide-cd: cmd 0x3 timed out
hda: lost interrupt
hda: lost interrupt
ide-cd: cmd 0x3 timed out
hda: lost interrupt

.............

以前启动都很正常，突然就不行了，到中途在 红色 字体的部分停了好久根据ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive 初步认为是光驱的问题，我的是PHILIPS的刻录机，我重新拔出来再插上去，还是老样子。

并且只有第一次启动时这样，重新启动后一切都正常。

烟雨平生

并且在
hda: lost interrupt 处要停好久还是启动不了。我的硬盘是 西部数据串口硬盘160G的

zzjjsswj

zzjjsswj@126.cojm

d00m3d

建议更新内核或 udev