根分区“/”空间不够，我该怎么办？

heshanxingzhe · 发表于 2007-11-5 00:54:37

大家好，我现在该怎么办，是重装呢，还是有别的解决办法？

我刚刚接触linux，一周前装了Fedora 7，用了近一周多的时间把好多软件装好，却发现“跟分区／”不够用了，只剩下几百M了，硬盘上又没有剩余空白空间了，哎，都怪自己在装系统的时候不注意分区。

系统空间：
[root@localhost active]# df -lh
文件系统             容量  已用可用已用% 挂载点
/dev/sda9          4.9G  4.5G  184M  97% /
/dev/sda8             99M 12M 82M  13% /boot
tmpfs                217M    0  217M 0% /dev/shm
/dev/sda11          17G  694M 16G 5% /home
/dev/sda5             10G  7.0G  3.1G  70% /mnt/wind
/dev/sda6             21G  9.5G 11G  48% /mnt/wine
/dev/sda7             15G  8.0G  7.1G  53% /mnt/winf
/dev/sda1          8.1G  4.4G  3.7G  55% /mnt/winc

分区信息：
[root@localhost active]# fdisk -l

Disk /dev/sda: 81.9 GB, 81964302336 bytes
255 heads, 63 sectors/track, 9964 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

Device Boot    Start       End    Blocks Id  System
/dev/sda1 *          1       1049    8426061 c  W95 FAT32 (LBA)
/dev/sda2          1050       9964 71609737+ f  W95 Ext'd (LBA)
/dev/sda5          1050       2354 10482381 7  HPFS/NTFS
/dev/sda6          2355       4965 20972826 7  HPFS/NTFS
/dev/sda7          4966       6923 15727603+ 7  HPFS/NTFS
/dev/sda8          6924       6936    104391 83  Linux
/dev/sda9          6937       7590    5253223+  83  Linux
/dev/sda10          7591       7721    1052226 82  Linux swap / Solaris
/dev/sda11          7722       9964 18016866 83  Linux

挂载点：
[root@localhost active]# mount
/dev/sda9 on / type ext3 (rw)
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
devpts on /dev/pts type devpts (rw,gid=5,mode=620)
/dev/sda8 on /boot type ext3 (rw)
tmpfs on /dev/shm type tmpfs (rw)
/dev/sda11 on /home type ext3 (rw,usrquota,grpquota)
/dev/sda5 on /mnt/wind type fuseblk (rw,nosuid,nodev,noatime,allow_other,default_permissions,blksize=4096)
/dev/sda6 on /mnt/wine type fuseblk (rw,nosuid,nodev,noatime,allow_other,default_permissions,blksize=4096)
/dev/sda7 on /mnt/winf type fuseblk (rw,nosuid,nodev,noatime,allow_other,default_permissions,blksize=4096)
/dev/sda1 on /mnt/winc type vfat (rw,codepage=936,iocharset=cp936)
none on /proc/sys/fs/binfmt_misc type binfmt_misc (rw)
sunrpc on /var/lib/nfs/rpc_pipefs type rpc_pipefs (rw)

去网上搜索，发现好像不能把已知分区的空间转到另外的分区上去，去搜下想把分区/home的空间挂载到跟分区/上，又好像不行。现在想装一些应用程序，用yum自动安装，又不会设置安装软件到分区/home上（上网搜了yum的用法，还是不会）结果造成根分区/空间不够，软件安装不了，我知道也可以先下载rpm包，然后用--prefix=<

ATH>，但有时，软件的依赖性很多，自己手动得花费很多时间，还是yum方便，但又好像yum对--prefix不支持（主要是我不会用，上网搜了很久也还是不会该yum的安装路径）。
搞到现在我有重装的冲动，请问大侠们，我现在该怎样做，我很不想重装啊，重装单装个驱动就害死我了。

主板：集成显卡、声卡、网卡（这里装驱动，我都装到很辛苦）昂达N61G，芯片组：
内存：512MB
处理器：AMD Athlon(tm)64 Processor 3000+ （64位的，也被害的不惨啊，很多软件64位装很麻烦）

请问大侠们，我现在该怎么办，是重装呢，还是有别的解决办法？

空间不够，提示安装不了：
[root@localhost eva]# yum install qt*
Loding "fastesmiror" pugin
Loaing "installonyn" plgi
Loading mirror speeds from cached hostfile
Setting up Install Process
Parsing package install arguments
Resolving Dependencies
--> Running transaction check
---> Package qt-sqlite.x86_64 1:3.3.8-7.fc7 set to be updated
---> Package qt-PostgreSQL.x86_64 1:3.3.8-7.fc7 set to be dated
。。。。。。。。。。。
---> Package exiv2.x86_64 0:0.14-1.fc7 set to be updated
---> Package jfsutils.x86_64 0:1.1.10-4.1 set to be updated

Dependencies Resolved

=============================================================================
Package                Arch    Version       Repository       Size
=============================================================================
Installing:
qt                   i386    1:3.3.8-7.fc7 7 updates          1.9 M
qt-devel             i386    1:3.3.8-7.fc7 updates          11 M
。。。。。。。。。。。。。
xfsprogs             x86_64    2.9.4-3.fc7    updates          1.3 M

Transaction Summary
=============================================================================
Install    31 Package(s)
Update    1 Package(s)
Remove    0 Package(s)

Total download size: 79 M
Is this ok [y/N]: y
Downloading Packages:
(1/32): qt4-devel-4.3.2-1 100% |=========================| 6.2 MB 03:40
。。。。。。。。。。。。
(32/32): qt-sqlite-3.3.8- 100% |=========================| 229 kB 00:08
Running Transaction Test
Finished Transaction Test

Transaction Check Error:
  installing package qt-devel-3.3.8-7.fc7 needs 8MB on the / filesystem
  installing package qt-3.3.8-7.fc7 needs 8MB on the / filesystem
  installing package exiv2-0.14-1.fc7 needs 9MB on the / filesystem
  installing package qt-designer-3.3.8-7.fc7 needs 14MB on the / filesystem
  installing package qt-ODBC-3.3.8-7.fc7 needs 14MB on the / filesystem
  installing package jfsutils-1.1.10-4.1 needs 16MB on the / filesystem
  installing package qt-config-3.3.8-7.fc7 needs 16MB on the / filesystem
  installing package qtpfsgui-1.8.12-1.fc7 needs 19MB on the / filesystem
  installing package qt4-qsa-devel-1.2.2-4.fc7 needs 21MB on the / filesystem
  installing package qt4-qsa-devel-1.2.2-4.fc7 needs 21MB on the / filesystem
  installing package qt4-mysql-4.3.2-1.fc7 needs 21MB on the / filesystem
  installing package qt4-devel-4.3.2-1.fc7 needs 33MB on the / filesystem

Error Summary
-------------
Disk Requirements:
  At least 200MB needed on the / filesystem.

上网搜到：把一些没多大用处的文件删掉还一些空间，例如：
/usr/share/doc/
/tmp
/var/tmp
等等，但终究不是长久之计。

heshanxingzhe · 发表于 2007-11-5 00:57:47

硬件信息：
[root@localhost ~]# lspci -v
00:00.0 RAM memory: nVidia Corporation C51 Host Bridge (rev a2)
      Flags: bus master, 66MHz, fast devsel, latency 0
      Capabilities: [44] HyperTransport: Slave or Primary Interface
      Capabilities: [e0] HyperTransport: MSI Mapping

00:00.1 RAM memory: nVidia Corporation C51 Memory Controller 0 (rev a2)
      Flags: 66MHz, fast devsel

00:00.2 RAM memory: nVidia Corporation C51 Memory Controller 1 (rev a2)
      Flags: 66MHz, fast devsel

00:00.3 RAM memory: nVidia Corporation C51 Memory Controller 5 (rev a2)
      Flags: 66MHz, fast devsel

00:00.4 RAM memory: nVidia Corporation C51 Memory Controller 4 (rev a2)
      Flags: bus master, 66MHz, fast devsel, latency 0

00:00.5 RAM memory: nVidia Corporation C51 Host Bridge (rev a2)
      Flags: bus master, 66MHz, fast devsel, latency 0
      Capabilities: [44] #00 [00fe]
      Capabilities: [fc] #00 [0000]

00:00.6 RAM memory: nVidia Corporation C51 Memory Controller 3 (rev a2)
      Flags: 66MHz, fast devsel

00:00.7 RAM memory: nVidia Corporation C51 Memory Controller 2 (rev a2)
      Flags: 66MHz, fast devsel

00:02.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1) (prog-if 00 [Normal decode])
      Flags: bus master, fast devsel, latency 0
      Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
      I/O behind bridge: 0000a000-0000afff
      Memory behind bridge: fd700000-fd7fffff
      Prefetchable memory behind bridge: 00000000fde00000-00000000fdefffff
      Capabilities: [40] Subsystem: nVidia Corporation Unknown device 0000
      Capabilities: [48] Power Management version 2

heshanxingzhe · 发表于 2007-11-5 00:59:46

Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable-
      Capabilities: [60] HyperTransport: MSI Mapping
      Capabilities: [80] Express Root Port (Slot+) IRQ 0

00:03.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1) (prog-if 00 [Normal decode])
      Flags: bus master, fast devsel, latency 0
      Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
      I/O behind bridge: 00009000-00009fff
      Memory behind bridge: fdd00000-fddfffff
      Prefetchable memory behind bridge: 00000000fdc00000-00000000fdcfffff
      Capabilities: [40] Subsystem: nVidia Corporation Unknown device 0000
      Capabilities: [48] Power Management version 2
      Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable-
      Capabilities: [60] HyperTransport: MSI Mapping
      Capabilities: [80] Express Root Port (Slot+) IRQ 0

00:04.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1) (prog-if 00 [Normal decode])
      Flags: bus master, fast devsel, latency 0
      Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
      I/O behind bridge: 0000b000-0000bfff
      Memory behind bridge: fd900000-fd9fffff
      Prefetchable memory behind bridge: 00000000fd800000-00000000fd8fffff
      Capabilities: [40] Subsystem: nVidia Corporation Unknown device 0000
      Capabilities: [48] Power Management version 2
      Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable-
      Capabilities: [60] HyperTransport: MSI Mapping
      Capabilities: [80] Express Root Port (Slot+) IRQ 0

00:05.0 VGA compatible controller: nVidia Corporation C51G [GeForce 6100] (rev a2) (prog-if 00 [VGA])
      Subsystem: nVidia Corporation Unknown device 0222
      Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 16
      Memory at fb000000 (32-bit, non-prefetchable) [size=16M]
      Memory at e0000000 (64-bit, prefetchable) [size=256M]
      Memory at fc000000 (64-bit, non-prefetchable) [size=16M]
      [virtual] Expansion ROM at 30000000 [disabled] [size=128K]
      Capabilities: [48] Power Management version 2
      Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-

00:09.0 RAM memory: nVidia Corporation MCP51 Host Bridge (rev a2)
      Subsystem: nVidia Corporation Unknown device cb84
      Flags: bus master, 66MHz, fast devsel, latency 0
      Capabilities: [44] HyperTransport: Slave or Primary Interface
      Capabilities: [e0] HyperTransport: MSI Mapping

00:0a.0 ISA bridge: nVidia Corporation MCP51 LPC Bridge (rev a2)
      Subsystem: nVidia Corporation Unknown device cb84
      Flags: bus master, 66MHz, fast devsel, latency 0

00:0a.1 SMBus: nVidia Corporation MCP51 SMBus (rev a2)
      Subsystem: nVidia Corporation Unknown device cb84
      Flags: 66MHz, fast devsel, IRQ 10
      I/O ports at 1c00
      I/O ports at 1c40
      Capabilities: [44] Power Management version 2

00:0a.2 RAM memory: nVidia Corporation MCP51 Memory Controller 0 (rev a2)
      Subsystem: nVidia Corporation Unknown device cb84
      Flags: 66MHz, fast devsel

00:0b.0 USB Controller: nVidia Corporation MCP51 USB Controller (rev a2) (prog-if 10 [OHCI])
      Subsystem: nVidia Corporation Unknown device cb84
      Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23
      Memory at fe02f000 (32-bit, non-prefetchable) [size=4K]
      Capabilities: [44] Power Management version 2

00:0b.1 USB Controller: nVidia Corporation MCP51 USB Controller (rev a2) (prog-if 20 [EHCI])
      Subsystem: nVidia Corporation Unknown device cb84
      Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22
      Memory at fe02e000 (32-bit, non-prefetchable) [size=256]
      Capabilities: [44] Debug port
      Capabilities: [80] Power Management version 2

00:0d.0 IDE interface: nVidia Corporation MCP51 IDE (rev a1) (prog-if 8a [Master SecP PriP])
      Subsystem: Unknown device f0de:cb84
      Flags: bus master, 66MHz, fast devsel, latency 0
      [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled]
      [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled]
      [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled]
      [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled]
      I/O ports at f400
      Capabilities: [44] Power Management version 2

00:0e.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller (rev a1) (prog-if 85 [Master SecO PriO])
      Subsystem: nVidia Corporation Unknown device cb84
      Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21
      I/O ports at 09f0
      I/O ports at 0bf0
      I/O ports at 0970
      I/O ports at 0b70
      I/O ports at e000
      Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
      Capabilities: [44] Power Management version 2
      Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/2 Enable-
      Capabilities: [cc] HyperTransport: MSI Mapping

00:10.0 PCI bridge: nVidia Corporation MCP51 PCI Bridge (rev a2) (prog-if 01 [Subtractive decode])
      Flags: bus master, 66MHz, fast devsel, latency 0
      Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
      I/O behind bridge: 0000c000-0000cfff
      Memory behind bridge: fdb00000-fdbfffff
      Prefetchable memory behind bridge: fda00000-fdafffff
      Capabilities: [b8] Subsystem: Gammagraphx, Inc. Unknown device 0000
      Capabilities: [8c] HyperTransport: MSI Mapping

00:10.2 Multimedia audio controller: nVidia Corporation MCP51 AC97 Audio Controller (rev a2)
      Subsystem: nVidia Corporation Unknown device cb84
      Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23
      I/O ports at dc00 [size=256]
      I/O ports at d800 [size=256]
      Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]
      Capabilities: [44] Power Management version 2

00:14.0 Bridge: nVidia Corporation MCP51 Ethernet Controller (rev a1)
      Subsystem: nVidia Corporation Unknown device cb84
      Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 20
      Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
      I/O ports at d400
      Capabilities: [44] Power Management version 2

00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
      Flags: fast devsel
      Capabilities: [80] HyperTransport: Host or Secondary Interface

00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
      Flags: fast devsel

00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
      Flags: fast devsel

00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
      Flags: fast devsel
      Capabilities: [f0] #0f [4010]

用dmesg查看：
[root@localhost ~]# dmesg|more
Linux version 2.6.21-1.3194.fc7 (kojibuilder@hammer2.fedora.redhat.com) (gcc ver
sion 4.1.2 20070502 (Red Hat 4.1.2-12)) #1 SMP Wed May 23 22:47:07 EDT 2007
Command line: ro root=LABEL=/ rhgb quiet
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009d400 (usable)
BIOS-e820: 000000000009d400 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001bef0000 (usable)
BIOS-e820: 000000001bef0000 - 000000001bef3000 (ACPI NVS)
BIOS-e820: 000000001bef3000 - 000000001bf00000 (ACPI data)
BIOS-e820: 000000001c000000 - 0000000020000000 (reserved)
BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 157) 0 entries of 3200 used
Entering add_active_range(0, 256, 114416) 1 entries of 3200 used
end_pfn_map = 1048576
DMI 2.2 present.
ACPI: RSDP 000F7D50, 0014 (r0 Nvidia)
ACPI: RSDT 1BEF3040, 0034 (r1 Nvidia AWRDACPI 42302E31 AWRD       0)
ACPI: FACP 1BEF30C0, 0074 (r1 Nvidia AWRDACPI 42302E31 AWRD       0)
ACPI: DSDT 1BEF3180, 65E2 (r1 NVIDIA AWRDACPI    1000 MSFT  100000E)
ACPI: FACS 1BEF0000, 0040
ACPI: SRAT 1BEF9880, 0090 (r1 AMD HAMMER       1 AMD       1)
ACPI: MCFG 1BEF9980, 003C (r1 Nvidia AWRDACPI 42302E31 AWRD       0)
ACPI: APIC 1BEF97C0, 0072 (r1 Nvidia AWRDACPI 42302E31 AWRD       0)
SRAT: PXM 0 -> APIC 0 -> Node 0
SRAT: Node 0 PXM 0 0-a0000
Entering add_active_range(0, 0, 157) 0 entries of 3200 used
SRAT: Node 0 PXM 0 0-20000000
Entering add_active_range(0, 0, 157) 1 entries of 3200 used
Entering add_active_range(0, 256, 114416) 1 entries of 3200 used
NUMA: Using 63 for the hash shift.
Bootmem setup node 0 0000000000000000-000000001bef0000
Zone PFN ranges:
  DMA          0 ->    4096
  DMA32       4096 ->  1048576
  Normal 1048576 ->  1048576
early_node_map[2] active PFN ranges
0:       0 ->    157
0:    256 -> 114416
On node 0 totalpages: 114317
  DMA zone: 56 pages used for memmap
  DMA zone: 1293 pages reserved
  DMA zone: 2648 pages, LIFO batch:0
  DMA32 zone: 1508 pages used for memmap
  DMA32 zone: 108812 pages, LIFO batch:31
  Normal zone: 0 pages used for memmap
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Setting APIC routing to physical flat
Using ACPI (MADT) for SMP configuration information
Nosave address range: 000000000009d000 - 000000000009e000
Nosave address range: 000000000009e000 - 00000000000a0000
Nosave address range: 00000000000a0000 - 00000000000f0000
Nosave address range: 00000000000f0000 - 0000000000100000
Allocating PCI resources starting at 30000000 (gap: 20000000:d0000000)
SMP: Allowing 2 CPUs, 1 hotplug CPUs
PERCPU: Allocating 43648 bytes of per cpu data
Built 1 zonelists.  Total pages: 111460
Kernel command line: ro root=LABEL=/ rhgb quiet
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 16384 bytes)
time.c: Detected 1808.349 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
Checking aperture...
CPU 0: aperture @ 154000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Memory: 440936k/457664k available (2319k kernel code, 16332k reserved, 1375k dat
a, 316k init)
Calibrating delay using timer specific routine.. 3618.53 BogoMIPS (lpj=1809267)
Security Framework v1.0.0 initialized
SELinux:  Initializing.
SELinux:  Starting in permissive mode
selinux_register_security:  Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 0/0 -> Node 0
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
Using local APIC timer interrupts.
result 12557986
Detected 12.557 MHz APIC timer.
Brought up 1 CPUs
sizeof(vma)=176 bytes
sizeof(page)=56 bytes
sizeof(inode)=560 bytes
sizeof(dentry)=208 bytes
sizeof(ext3inode)=760 bytes
sizeof(buffer_head)=104 bytes
sizeof(skbuff)=248 bytes
sizeof(task_struct)=1888 bytes
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:05.0
PCI: Transparent bridge - 0000:00:10.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK5] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LACI] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0
ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
pnp: 00:01: ioport range 0x1000-0x107f has been reserved
pnp: 00:01: ioport range 0x1080-0x10ff has been reserved
pnp: 00:01: ioport range 0x1400-0x147f has been reserved
pnp: 00:01: ioport range 0x1480-0x14ff has been reserved
pnp: 00:01: ioport range 0x1800-0x187f has been reserved
pnp: 00:01: ioport range 0x1880-0x18ff has been reserved
pnp: 00:01: ioport range 0x2000-0x207f has been reserved
pnp: 00:01: ioport range 0x2080-0x20ff has been reserved
pnp: 00:01: iomem range 0xfefe0000-0xfefe01ff has been reserved
pnp: 00:01: iomem range 0x1c000000-0x1fffffff could not be reserved
pnp: 00:0c: iomem range 0xf0000000-0xf3ffffff could not be reserved
pnp: 00:0d: iomem range 0xd1800-0xd3fff has been reserved
pnp: 00:0d: iomem range 0xf0000-0xf7fff could not be reserved
pnp: 00:0d: iomem range 0xf8000-0xfbfff could not be reserved
pnp: 00:0d: iomem range 0xfc000-0xfffff could not be reserved
PCI: Bridge: 0000:00:02.0
  IO window: a000-afff
  MEM window: fd700000-fd7fffff
  PREFETCH window: fde00000-fdefffff
PCI: Bridge: 0000:00:03.0
  IO window: 9000-9fff
  MEM window: fdd00000-fddfffff
  PREFETCH window: fdc00000-fdcfffff
PCI: Bridge: 0000:00:04.0
  IO window: b000-bfff
  MEM window: fd900000-fd9fffff
  PREFETCH window: fd800000-fd8fffff
PCI: Bridge: 0000:00:10.0

heshanxingzhe · 发表于 2007-11-5 01:02:11

谢谢大家看我的贴！！
现在好怀念WINDOWS XP 啊，还是WINDOWS 方便。

亚森罗平 · 发表于 2007-11-5 02:12:00

sudo cd /var/cache/yum/仓库类别/packages
mv packages packages pack.backup
ln -s /mnt/d/某目录 /var/cache/yum/仓库类别/packages

做链接是最方便的了，百试百灵

客游 · 发表于 2007-11-5 09:10:04

直接将其他分区链接上去就可以了

LongerZ · 发表于 2007-11-5 09:13:38

看样子，你有单独的/home分区，而且也不小，干脆将/home分区和/usr掉个个，将/usr分出来单独挂载，/home随/分区；或者cp(mv)原来/home的分区内容到备份分区，再从sda11划分出一个分区挂载/usr (因为一般/usr目录比较大)

heshanxingzhe · 发表于 2007-11-5 10:45:03

看样子，你有单独的/home分区，而且也不小，干脆将/home分区和/usr掉个个，将/usr分出来单独挂载，/home随/分区；或者cp(mv)原来/home的分区内容到备份分区，再从sda11划分出一个分区挂载/usr (因为一般/usr目录比较大)

不好意思，不是很明白你的意思，怎样“将/usr分出来单独挂载，/home随/分区”

wq1977 · 发表于 2007-11-5 11:36:28

如果你不怕危险，我教给你一个危险的办法：

resize2fs为系统自带的分区调整工具，这个工具的作用是安全调整ext2或者ext3的分区大小。使用的方法是：

resize2fs -p /dev/sda9 新大小

如果你想扩大某个分区，首先使用fdisk工具来保证你要操作的分区可以被安全的扩大，然后使用这个工具扩展/dev/sda9

针对你目前的情况，如果是我，我会: 使用livecd（ubuntu的安装盘就可以）重新启动,然后备份原先的/Home,使用fdisk工具删除/dev/sda10和/dev/sda11,将sda9的大小调整为10G(注意调整前后的起始柱面位置相同),然后在后面创建1G的交换分区和剩余空间的Home分区，然后LiveCD重启，再使用resize2fs工具扩展/dev/sda9到10G，检查原始根分区的/etc/fstab是否需要修改并且进行必要的修改（通常不需要，除非你的/home使用的什么UUID之类的标示的，你可以直接把它更改为/dev/sda11），恢复/Home分区的数据, 然后重新启动你的系统。

修改完成。

我自己这么搞过没有问题，不过如果你使用这种方法，出了事不要来找我。呵呵。

LongerZ · 发表于 2007-11-5 12:05:16

Post by heshanxingzhe;1777455
不是很明白你的意思，怎样“将/usr分出来单独挂载，/home随/分区”

你的 sda11 是/home分区吧，切记操作前请先备份！
我的意思是要不将当前sda11挂载为/usr ，要不备份后在划出一个分区用来挂载/usr，参考fstab为：

/dev/sdaX /usr reiserfs noatime,notail 0 0

		自动登录	找回密码
密码			注册

根分区“/”空间不够，我该怎么办？

LongerZ兄